Majestic Biltmore SL1100 страница 4 Скачать руководство пользователя

Страница: 4 / 45

Majestic Biltmore Series • SB100 • 4013-303 Installers Manual • Rev H • 08/20

WARNING! Risk of Fire!

Hearth & Home Technologies

disclaims any responsibility for, and the warranty and

agency listing will be voided by the following actions.

DO NOT:

• install or operate damaged fireplace

• modify fireplace

• install other than as instructed by Hearth & Home

Technologies

• operate the fireplace without fully assembling all

components

• overfire

• install any component not approved by Hearth & Home

Technologies

• install parts or components not Listed or approved
Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel

- Iron

- Brick

- Tile

- Concrete

- Slate

- Glass

- Plasters

• Materials reported as passing

ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood

- Compressed paper

- Plant fibers

- Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; flame proofed or

not, plastered or un-plastered

Product Specific & Important Safety Information

A. Fireplace Certification

WARNING: This product and the fu-

els used to operate this product (wood

and wood pellets), and the products of

combustion of such fuels, can expose

you to chemicals including carbon black,

which is known to the State of California

to cause cancer and carbon monoxide,

which is known to the State of California to

cause birth defects or other reproductive

harm. For more information go to: www.

P65Warnings.ca.gov.

This fireplace may be installed in sleeping rooms. This

fireplace is not approved for manufactured housing. If in

stalled with a gas log set, provisions for the National Fuel

Gas Code must be met.
This fireplace has been tested and listed for use with

the optional components specified in this manual. These

optional components may be purchased separately and

installed at a later date. An outside air kit, gas insert, gas

log set or gas log-lighter should be installed at the time of

fireplace installation.

This fireplace system has been tested and listed in accor

dance with UL 127 standards by Underwriters Laborato

ries Inc. for installation and operation in the United States.

Содержание Biltmore SL1100














































Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Похожие инструкции для Biltmore SL1100

Бренды по названию

Популярные бренды

Majestic Biltmore SL1100, Руководство по установке

Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Похожие инструкции для Biltmore SL1100

Бренды по названию

Популярные бренды