Majestic Biltmore SL1100 страница 28 Скачать руководство пользователя

Страница: 28 / 45

Majestic Biltmore Series • SB100 • 4013-303 Installers Manual • Rev H • 08/20

Shrouds

3 in. (76 mm) tall legs

Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap

Length x Width to fit inside shroud

Figure 6.1 Radiation Shield

WARNING! Risk of Fire!

Shrouds must be constructed

as specified. Improper construction may overheat

chase top.

NOTICE:

Some regional codes require an agency-Listed

shroud. Consult your local building officials.

Shrouds may be field constructed where permitted by

regional building codes.

The shrouds must be constructed from minimum .018

in. (26 ga) thick aluminzed steel.
Some shrouds require a radiation shield. Use where

specified.

A. Radiation Shield

Radiation shield must be constructed of minimum 26 ga

thick sheet metal.

B. Field Constructed Shrouds

The following field constructed shroud designs have

been tested for HHT fireplace systems and termination

caps.

3 in (76 mm)

minimum

Min.

Base Dim.

Min.

Base Dim.

Min.

Top Dim.

Min.

Top Dim.

Min. Opening

Width

Min. Opening

Width

Radiation

Shield

14 1/2 in. (368 mm)

maximum height

Figure 6.2 Open Top Shroud Dimensions (with Radiation Shield)

Figure 6.3 Shroud & TR Series cap with no Radiation Shield

TR11/11T

TR11/11T TV

Min. Base Dims.

32 x 32

26 x 26

813 x 813

660 x 660

Radiation Shield

Required

Radiation

Shield Not

Required

Min. Top Dims.

29 x 29

23 x 23

737 x 737

584 x 584

Min. Opening Width

26 x 26

20 x 20

660 x 660

508 x 508

1. Open Top Shroud

TR11/TR11T TV (top vented) caps do not require radia

tion shield.

TR11/TR11T caps require radiation shield unless in

stalled partially above the shroud. The TR cap must be

raised to the minimum dimensions (or greater) above the

shroud or install a TR-TVK. Refer to Figure 6.3.

6" Min.

Above the

Shroud.

Storm

Collar

Shroud

Leg

(SHROUD)

(TR Series)

Flue

Shroud

Leg

3 in (76 mm)

air space from

bottom of shroud

to top of chase.

Maximum Height

14 1/2 in. (368 mm)

Chase Top

Содержание Biltmore SL1100














































Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Похожие инструкции для Biltmore SL1100

Бренды по названию

Популярные бренды

Majestic Biltmore SL1100, Руководство по установке

Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Похожие инструкции для Biltmore SL1100

Бренды по названию

Популярные бренды