Majestic Biltmore SL1100 Скачать руководство пользователя страница 35

Страница: 35 / 45

Majestic Biltmore Series • SB100 • 4013-303 Installers Manual • Rev H • 08/20

D. Mantel and Wall Projections

The combustible mantel may have a maximum depth of 12

in. (305mm), positioned 20 in. (508mm) above the open

ing. Combustible trim pieces that project no more than 1

1/2 in. (38 mm) from the face of the fireplace can be placed

no closer than 6 in. (152 mm) from the top of the opening.

Combustible trim must not cover:

• the metal surfaces of the fireplace

• where the non-combustible board is placed over the

metal surfaces

• the space between the metal face of the fireplace and

framing members

Combustible Wall

2 x 4 stud wall

Front Standoffs

Measured from top of fireplace opening

12 in./305 mm

Mantel

1 1/ 2 in./38 mm

maximum

6 in./152 mm

minimum

20 in./508 mm

minimum

12 in./305 mm

minimum

Combustible

Decorative Facing

Grid represents 1 in. squares

Seal joint with

non-combustible

sealant to prevent heat

from being drawn into

the wall cavity

7 ft (2134 mm)

minimum

base of fireplace

to ceiling

Non-combustible

Decorative Facing

such as: Steel, iron,

brick, tile, concrete,

slate, tile, plasters

DO NOT cover any

air openings in the

face of the fireplace.

Figure 7.11 Mantel Specifications

WARNING! Risk of Fire!

• You must seal around the finishing material to fireplace.

Содержание Biltmore SL1100














































Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Бренды по названию

Популярные бренды

Majestic Biltmore SL1100, Руководство по установке

Результаты поиска

Содержание Biltmore SL1100

Отзывы:

Бренды по названию

Популярные бренды