Majestic 500DVH Series страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 72

background image

1

56D3049

INSTALLATION PRECAUTIONS

Consult local building codes before beginning the installation. The installer must make sure to select the proper vent system

for installation. Before installing vent kit, the installer must read this fireplace manual and vent kit instructions.
Only a qualified installer/service person should install the venting system. The installer must follow these safety rules:
  •  Wear gloves and safety glasses for protection.
  •  Use extreme caution when using ladders or when on rooftops.
  •  Be aware of electrical wiring locations in walls and ceilings.
The following actions will void the warranty on your venting system:
  •  Installation of any damaged venting component.
  •  Unauthorized modification of the venting system.
  •  Installation of any component part not manufactured or approved by MHSC
  •  Installation other than permitted by these instructions.

FINISHING MATERIAL

NOTE: Any remote wiring (i.e. remote control, wall switch, and optional fan) must be done prior to final

finishing to avoid costly reconstruction.

INSTALLATION INFORMATION

Only noncombustible materials (i.e. brick, tile, slate, steel, or other materials with a UL fire rating of Zero) may be used to

cover the black surface of the appliance. A 300°F minimum adhesive may be used to attach facing materials to the black

surface. If joints between the finished wall and the fireplace surround are sealed, a 300°F minimum sealant material (General

Electric RTV103 or equivalent) must be used.

VENT INSTALLATION

W

ARNING

Never obstruct or modify the air inlet

or outlet grills (louvers). This may

create a fire hazard.

W

ARNING

Read all instructions completely and thoroughly before attempting installation. Failure

to do so could result in serious injury, property damage or loss of life. Operation of

improperly installed and maintained venting system could result in serious injury,

property damage or loss of life.

NOTICE

Failure to follow these instructions

will void the warranty.

«
...
10
11
12
13
14
...
»

Содержание 500DVH Series









































































Отзывы:

Нет отзывов

Похожие инструкции для 500DVH Series

Home VERSANORA VNF-00115

Бренд: Teamson Страницы: 21

Бренд: Majestic Страницы: 44

Бренд: Pacific energy Страницы: 24

Бренд: HPC Страницы: 10

Бренд: Draftbooster Страницы: 13

Бренд: Napoleon Страницы: 80

Бренд: Bluegrass Living Страницы: 8

Бренд: Heat & Glo Страницы: 26

Бренд: Nordpeis Страницы: 48

Бренд: Lennox Hearth Products Страницы: 42

Бренд: Heat & Glo Страницы: 57

Бренд: Coleman Страницы: 2

Бренд: Element4 Страницы: 56

Бренд: Nibe Страницы: 20

Бренд: Spatherm Страницы: 24

Бренд: Spartherm Страницы: 28

Бренд: Heat&Glo Страницы: 20

Бренд: vision trimline Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды