background image

9

360DVS Series Direct Vent Fireplaces

10006326

Final Finishing

1. Choose the unit location.

2. Place the unit into position and secure it to the floor

with 1

¹⁄₂

” (38mm) screws or nails. Holes to secure

the unit to the floor are located behind the access
door grille on the left and right sides of the unit.

3. Frame in the fireplace with a header across the top.

It is important to allow for the finished wall face when
setting the depth of the frame.

4. Drywall (sheetrock) or wood material may be placed

with a zero clearance to the top edges of the appli-
ance when finishing walls above sides of the appli-
ance with glass windows. NOTE: Attach wall
finishing to constructed frame, not the appli-
ance.

5. On 360DVSL and 360DVSR, drywall, wood, or wood

molding may be placed with zero clearance to the
rear wall of the unit, along the vertical edge formed
by the standoffs, to intersection of the rear wall, to
the side wall having the small glass window. NOTE:
Attach wall finishing to constructed frame, not
the appliance.

Framing & Finishing

Noncombustible materials such as brick or tile may be
extended over the edges of the face of the appliance.
DO NOT cover any vent or grille panels.

If a Trim Kit is going to be installed on the fireplace, the
brick or tile will have to be installed flush with the edges
of the appliance.

12345678901234567890123456789012

12345678901234567890123456789012

12345678901234567890123456789012

12345678901234567890123456789012

12345678901234567890123456789012

12345678901234567890123456789012

Gas Inlet & Manifold Pressures

Natural

LP (Propane)

Inlet Minimum

4.5” w.c.

11.0” w.c.

Inlet Maximum

14.0” w.c.

14.0” w.c.

Manifold Pressure

3.5” w.c.

10.0” w.c.

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

Max.

Max.

Input

Input

Model

Fuel

Gas Control

BTU/h

BTU/h

360DVS2RN

Nat

Millivolt

38,000

26,600

360DVS2RP

Prop

Millivolt

38,000

28,500

360DVS2EN

Nat

24V Hi/Lo

38,000

26,600

360DVS2EP

Prop

24V Hi/Lo

38,000

28,500

360DVS3RN

Nat

Millivolt

38,000

26,600

360DVS3RP

Prop

Millivolt

38,000

28,500

360DVS3EN

Nat

24V Hi/Lo

38,000

26,600

360DVS3EP

Prop

24V Hi/Lo

38,000

28,500

360DVSLRN

Nat

Millivolt

38,000

26,600

360DVSLRP

Prop

Millivolt

38,000

28,500

360DVSLEN

Nat

24V Hi/Lo

38,000

26,600

360DVSLEP

Prop

24V Hi/Lo

38,000

28,500

360DVSRRN

Nat

Millivolt

38,000

26,600

360DVSRRP

Prop

Millivolt

38,000

28,500

360DVSREN

Nat

24V Hi/Lo

38,000

26,600

360DVSREP

Prop

24V Hi/Lo

38,000

28,500

Gas Specifications

360DVS2/ 360DVS3/ 360DVSL/ 360DVSR

CERTIFIED TO

ANSI Z21.88-2002/ CSA  2.33-2002

Vented Gas Fireplace Heaters

Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370 m) above sea level.

For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/or local codes
having jurisdiction.

In Canada, please consult provincial and/or local
authorities having jurisdiction for installations
above 4,500 feet (1,370 m).

When purging the gas lines, the window

frame assembly must be removed.

The gas pipeline can be brought in through the vent
end of the fireplace as well as the bottom. Knockouts
(to allow gas pipe installation and testing any gas
connection) are provided on the bottom behind the
valve. It is most convenient to bring the gas line in from
the vent end of the valve, as this allows fan installation
or removal without disconnecting the gas line.

The gas line connection can be made with properly
tinned 3/8” copper tubing, 3/8” rigid pipe, or an ap-
proved flex connector. Since some municipalities have
additional local codes, it is always best to consult your
local authority and the CSA-B149.1 installation codes.

For USA installations, consult the current National Fuel
Gas Code, ANSI Z223.1/NFPA 54.

Always check for gas leaks with a mild
soap and water solution. Do not use an
open flame for leak testing.

Gas Line Installation

1/2” Gas Supply

1/2” NPT X 1/2” Flare Shut-Off Valve

3/8” Flex Line
(From Valve)

FP297a

Fig. 5  Gas shutoff valve and flex connector.

Содержание 360DVS2









































Отзывы: