22
I
NSTALLATION
THE PASSION PEOPLE
www.magura.com
F
ITTING
THE
REMOTE
CONTROL
LEVER
(RCL²)
L
You will notice that DLO² is suitable for remote control because the blue
dial is returned to its original position by a return spring if turned by hand.
Blue dials that do not have a return spring do not support remote control
with RCL²! However, retrofitting is possible at a MAGURA service centre.
DLO³ is not suitable for remote control!
Danger of accident due to faulty installation work.
h
Make sure that the RCL² cannot interfere with brake and gear shift
actuation and function in any lever position.
Damage to material due to faulty installation work.
h
Never fit the clamps in the wider area of the handlebar.
h
Never exceed the maximum tightening torques.
There are 3 different fastening options for the RCL²
[
E1
]
:
h
Standard clamp
(
1
)
– for fitting next to the brake lever.
h
Standard clamp with spacer
(
2
)
and long clamping screw
(
3
)
– for fitting
next to the brake lever in combination with twist shifters.
h
Remote mix clamp
(
4
)
– only for direct fitting to brake levers of MAGURA
MT Series and HS Series (MAGURA rim brakes) as of model year 2011.
L
RCL² for DLO² is generally mounted on the right
[
E2
]
– however, it can
be mounted on the left side if required.
)
Define the position of the standard clamp on the handlebar.
Î
Make sure that the brake and gear shift actuation and function is not
impaired in any RCL² lever position.
Î
The lever
(
5
)
and return dial
(
6
)
on the RCL² must be easily reachable.
)
Tighten the clamping screw
(
7
)
(
3
)
on the standard clamp with a tighten-
ing torque of
max. 3 N·m (27 lbf·in)
.
)
Tighten the sleeve nuts
(
8
)
on the Remote Mix clamp with a tightening
torque of
max. 3 N·m (27 lbf·in)
.
Fit the RCL² Bowden cable
Danger of accident due to faulty installation work.
h
Make sure that the Bowden cables on the RCL² can never interfere with
steering.
Î
The outer sleeve must be laid via the shortest route, without torsion or
kinking, between the stops
(
9
)
on the RCL² and the fork crown
[
E2
]
.
)
Shorten the outer sleeve of the Bowden cable with suitable Bowden
cable pliers.
)
Make sure that the lever on the RCL² is relieved – press the return dial
if necessary.
)
Feed the inner cable through the RCL², outer sleeve and stop on the
fork crown.
)
Make sure that the outer sleeve is firmly seated in the stops.
Fit the inner DLO² cable
[
E3
]
:
)
Remove the cover on the “DLO²” by unscrewing counter-clockwise.
)
Loosen the clamping screw
(
10
)
by 2–3 turns.
)
Tension the inner cable and insert it into the groove on the rotating dial
and under the washer on the clamping screw and hold in place.
)
Tighten the clamping screw with a tightening torque of
max. 2 N·m
(18 lbf·in)
.
)
Trim the inner cable to a length of approx 2 cm after the clamping
screw.
)
Push the end of the inner cable through the cutout into the inside of the
rotating dial.
)
Replace the cover on the “DLO²” by screwing it on clockwise.
)
Retension the inner cable after the first 10–20 actuations.
Содержание TS6
