61
WT Weight Dispense Rate (grams/second)
TI Time
Set AUTOMATICALLY by the Flow Rate Calibration routine
WT and TI set the flow rate or dispense rate of each material. These can be set
manually, set by the
Flow
Rate Calibration
routine, and adjust automatically after
each cycle.
After a change in auger size, or substantial change in material flow rate, WT / TI can
be adjusted using the
Flow
Rate Calibration
to set a new flow rate automatically.
PO 00000
PO - Pulsed Output - For Micro Pulse Valves
PO sets the ON and OFF time, in 10ths of a second, of the specified component for
a "pulsed" output. First three digits (001xx) sets ON time. Last two digits (xxx01)
sets OFF time. Recommended setting: 00101. 00000 disables pulsing.
SE 01000
SE – SETTING UPPER LIMIT - Set an upper limit on the setting, limit access
1st digit – When a 1 is entered as the first digit of this parameter, (1xxxx),
setting entries will be prompted for the Admin password.
Last 4 digits are the upper setting limit. Uses the component’s decimal place for the
decimal location. 01000 disables upper limit.
SL 01000
SL – SETTING LOWER LIMIT – Set a lower limit on the setting
When enabled, the setting will be held to the lower limit in the component’s SL
parameter. Enabled is a value ranging from 00001 - 00999 or 00001 - 09999 in 4-
digit mode. Uses the component’s decimal place for the decimal location. 00000
disables lower limit.
SE and SL On-Screen Indicator – See Component Setpoint Control on page 44.
XT 00000
Sets decimal place in a component setting
00000 = XX.X
(Default)
00010 = X.XX
00100 = .XXX
NC 00010
Allowable GRAM error with NO correction (grams or 10ths of grams)
This is the acceptable error range for each component to prevent hunting. Adjusted
automatically over an extended time period (20 cycles) to match the flow
characteristics of each material. 29999 disables.
MI
Set AUTOMATICALLY by Flow Rate Calibration and 10 cycles after power up
MI value is set to 80 percent of the amount of material, in grams, that can feed in
one second based on normal dispense rates. Power-up always resets MI to 00001.
After 10 cycles have occurred without retries.
Содержание FLEXBUS Lite
