Example of emergency entry of the personal code - 6795
1. Turn on the ignition and start to count the LED flashes.
2. After the sixth flash (the first digit of the code - 6) switch off the ignition - LED
will start to count the second digit.
3. After the seventh flash (the second digit of the code - 7) turn on the ignition – LED
will start to count the third digit.
4. After the ninth flash (the third digit of the code - 9) switch off the ignition– LED
will start to count the fourth digit.
5. After the fifth flash (the fourth digit of the code - 5) turn on the ignition.
Code unblocking of the engine
If "Personal code when disarming" function is programmatically activated, then eve-
ry time after disarming the system to unblock the engine will be needed to enter the first
digit of a personal code.
By correctly entering the first digit of the code - the engine is unblocked and the
LED, for conspiracy, will finish a series of flashes after 10th flash.
If the first digit of the code will be entered incorrectly, the engine unblocking can be
made only by entering a full personal code.
Control with the ignition on
Remote key fob button
– closing the central door locking
Remote key fob button
– opening the central door locking (two stage)
Remote key fob button
– supply a short light signal (0.2 seconds)
Remote key fob button
–
code entry / remote control / alarm on
Switching off the alarm is carried out by pressing any remote key fob button.
Automatic control of the central door locking
Central door locking can be automatically closed, depending on the produced pro-
gram settings by the installer:
4 seconds after the switching on the ignition;
when motion sensor is triggered;
when you turn off the parking brake;
when you turn off the parking.
Central door locking can be automatically opened:
when you turn off the ignition;
when turn on the parking brake;
when you turn on the parking
Note:
Functions of automatic central door locking are disabled at open doors to
avoid damage to locks.
M880
OPERATION MANUAL
11
Protection against forcible theft
Protection program against forcible car theft is designed to protect the vehicle and its
owner after disarming the system and engine unblocking.
AntiHiJack from the driver's door
The function would require entering the first digit of a personal code after each door
opening and subsequent switching on the ignition.
Function is cocked when you open the door. When the ignition is switched - LED in-
dicator lights up and the program is started to prevent the forcible theft.
To reset the program, press the remote key fob button
set number of times (deter-
mined by the first digit of the code) - LED indicator turns off.
If after a set time protection program is not reset, the system will simulate a gradually
increasing in duration failures of the engine.
At this stage it is still possible to reset the program by entering the first digit of a per-
sonal code.
If protection program will not be reset, failures of the engine gradually lead to a com-
plete stop engine and the inability to re-start engine.
Message: "Alert! Armed assault!" will be sent to the second phone number for SMS-
messages in this case.
The engine will be blocked before the appointed time at any stage of work of the pro-
tection program when ignition switching off or when you enter the wrong first digit of a
personal code.
Reset of the protection program against forcible car theft after the final engine block-
ing can be achieved only by entering a complete personal code (see "Entering a personal
code").
Note 1:
In order that AntiHiJack function from the driver's door is cocked just from
the driver's door, the installer should necessarily share the control circuits of driver and
passenger doors.
Note 2:
Delay time of simulation of engine failure can be programmed in a wide
range - from 5 seconds to 10 minutes. AntiHiJack function from the driver's door is pro-
grammatically disabled in the factory settings.
AntiHiJack from the ghost button
The function assumes performance of certain actions by the vehicle owner to activate
and reset program for the protection against forcible car theft.
You can use two different versions of the vehicle protection and its owner against
forcible car theft: active and passive protection.
Active protection:
In the event of any danger or threat from third parties should be
enabled any standard or additional electrical equipment, pre-determined by the install-
er, like "ghost button". When the ignition is switched on - LED indicator lights up and the
program starts protection against forcible car theft. If "ghost button" is already activated
when the ignition on - protection program will start immediately.
OPERATION MANUAL
M880
12
