Magnum Energy MM Series Скачать руководство пользователя

Страница: 12 / 44

2010 Magnum Energy, Inc

2.0 Installation

2.0 Installation

Pre-Installation

Before installing the inverter, read

the entire Installation section. The

more thorough you plan in the beginning, the better your inverter

needs will be met.

WARNING:

Installations should be performed by quali

personnel, such as a licensed or certi

ed electrician. It

is the installer’s responsibility to determine which safety

codes apply and to ensure that all applicable installation

requirements are followed. Applicable installation codes

vary depending on the speci

c location and application of

the installation.

Info:

Review the “Important Product Safety Information”

on page ii and the “Important Battery Safety Instructions”

on page iii before any installation.

The basic system diagram shown in Figure 6

should be reviewed to

assist you in planning and designing your installation.

Unpacking and Inspection

Carefully remove the MM Series inverter from its shipping container

and inspect all contents. Verify the following items are included:

−

The MM Inverter

−

Red and black DC terminal covers

−

AC access cover with two screws

−

Two 1/2” hex-head kep nuts (installed on the DC terminals)

−

Battery Temperature Sensor (battery charger models only)

−

MM Series Owner’s Manual

If items appear to be missing or damaged, contact your authorized

Magnum Energy dealer or Magnum Energy.

If at all possible, keep your shipping box. It will help protect your in-

verter from damage if it ever needs to be returned for service.

Save your proof-of-purchase as a record of your ownership; it will also

be needed if the unit should require in-warranty service.

Record the unit’s model and serial number in the front of this manual

in case you need to provide this information in the future. It is much

easier to record this information now, instead of trying to gather it

after the unit has been installed.

Содержание MM Series













































Результаты поиска

Содержание MM Series

Отзывы:

Похожие инструкции для MM Series

Бренды по названию

Популярные бренды

Magnum Energy MM Series, Руководство пользователя

Результаты поиска

Содержание MM Series

Отзывы:

Похожие инструкции для MM Series

Бренды по названию

Популярные бренды