Magnum Energy MM Series Скачать руководство пользователя

Страница: 3 / 44

2010 Magnum Energy, Inc

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains important safety instructions that must be fol-

lowed during the installation and operation of this product. Read all

instructions and safety information contained in this manual before

installing or using this product.
• All electrical work must be performed in accordance with local, state,

and federal electrical codes.

• This product is designed for indoor/compartment installation. It must

not be exposed to rain, snow, moisture, or liquids of any type.

• Use insulated tools to reduce the chance of electrical shock or

accidental short circuits.

• Remove all jewelry such as rings, watches, bracelets, etc., when

installing or performing maintenance on the inverter.

• Always disconnect the batteries or energy source prior to installing

or performing maintenance on the inverter. Live power may be pres-

ent at more than one point since an inverter utilizes both batteries

and AC. Turning off the inverter may not reduce this risk. As long as

AC power is connected, it will pass thru the inverter regardless of the

ON/OFF power switch setting.

• Always verify proper wiring prior to starting the inverter.
• Do not operate the inverter if it has been damaged.
• Do not dismantle the inverter; there are no user-serviceable parts

contained in this product. Attempting to service the unit yourself

could cause electrical shock. Internal capacitors remain charged after

all power is disconnected.

• No AC or DC disconnects are provided as an integral part of this

inverter. Both AC and DC disconnects must be provided as part of

the system installation.

• No overcurrent protection for the battery supply is provided as an

integral part of this inverter. Overcurrent protection of the battery

cables must be provided as part of the system installation.

• No overcurrent protection for the AC output wiring is provided as an

integral part of this inverter. Overcurrent protection of the AC output

wiring must be provided as part of the system installation.

SAVE THESE INSTRUCTIONS

Terminology
AC source or External AC power

- refers to Alternating Current (AC)

provided by the utility electric power grid or from a generator. In some

applications this is referred to as shore power.

AE application

- typically refers to using the inverter in an system that

uses Alternative Energy (e.g., solar, wind, or hydro). This term is also

used to refer to inverters used in a home, of

ce, or a cabin installation.

Mobile application

- refers to inverters used in a Recreation Vehicle

(RV), boat, or a truck installation.

Содержание MM Series













































Результаты поиска

Содержание MM Series

Отзывы:

Похожие инструкции для MM Series

Бренды по названию

Популярные бренды

Magnum Energy MM Series, Руководство пользователя

Результаты поиска

Содержание MM Series

Отзывы:

Похожие инструкции для MM Series

Бренды по названию

Популярные бренды