manualshive.com logo in svg

Magnetek Telemotive TelePendant, Руководство по программированию и эксплуатации, Страница: 25 / 56

Поделиться
Скачать
Magnetek Telemotive TelePendant Скачать руководство пользователя страница 25

Section 5 – Programming (Continued) 

 22  

5-1.2.

 

Changing Transmitter Access Codes. 

5-1.2.1.

 

tele

Pendant

 Access Code Programming. 

For detailed instructions on setting parameters including access codes see Section 5-3.2. 

tele

Pendant Programming. 

  

WARNING

 

AFTER CHANGING THE ACCESS CODES ON THE TRANSMITTER, TEST THE UNIT BY TURNING IT ON AND 
OFF NEAR THE APPROPRIATE RECEIVER. IF THE RECEIVER DOES NOT RESPOND, DO NOT ACTIVATE A 
FUNCTION BUTTON! THE TRANSMITTER MAY HAVE THE WRONG ACCESS CODE, WHICH COULD MOVE 
ANOTHER CRANE. RE-CHECK THE ACCESS CODE IN THE TRANSMITTER AND RETEST. FAILURE TO 
FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. 

NOTE 

IN EVENT PROGRAMMING OF ACCESS CODES IS REQUIRED, TAKE SPECIAL

 

CARE TO CORRECTLY 

LOCATE ACCESS CODE SWITCHES A AND B. LOOK FOR THE LABELS A AND B ON THE PRINTED CIRCUIT 
BOARD NEAR THE RESPECTIVE SWITCHES. DETERMINE THEIR ORIENTATION. THE SWITCHES MAY 
NUMBER FROM LEFT TO RIGHT OR RIGHT TO LEFT. LOOK FOR THE NUMBERING ON THE SWITCHES. 
MATCH ACCESS CODES A1, A2, - -- B1, B2 ETC.  

After changing the access code, test the receiver (s) with a matching transmitter. (If the red LED “Wrong Access Code” 
comes ON in the receiver only while transmitting receiver the code does not match, recheck the access code settings). See 
receiver manual for LED location. 

  

WARNING

 

THE ACCESS CODES IN THE RECEIVER ARE UNIQUE AND FACTORY PRESET. DO NOT CHANGE THESE 
ACCESS CODES UNLESS YOU ARE REPLACING AN EXISTING RECEIVER AND ITS ACCESS CODE. 
CHANGING THIS CODE COULD MAKE IT COMMON WITH ANOTHER RECEIVER ACCESS CODE, WHICH 
COULD MOVE ANOTHER CRANE. NO TWO SYSTEMS IN ANY LOCATION SHOULD EVER HAVE THE SAME 
ACCESS CODES INDEPENDENT OF FREQUENCY. FAILURE TO FOLLOW THIS WARNING COULD RESULT 
IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. 

  
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Telemotive TelePendant

























































Отзывы:

Нет отзывов