Magnetek GPD 333 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 81

background image

WARNING

Do not touch circuit components until main input power has been
turned off and "CHARGE" lamp is extinguished. The capacitors
are still charged for up to 5 minutes and can be quite dangerous.

Do not connect or disconnect wires and connectors while power is
applied to the circuit.

CAUTION

The GPD 333 leaves the factory with constants initialized for
external 2-Wire control and constant

no–00 set to 01 . Before

using either initialization function of this constant, know your con-
trol wiring configuration :

08 = Factory 2-Wire control initialization ( maintained Run contact )
09 = Factory 3-Wire control initialization ( momentary Start /Stop input )

Entering either initialization code returns all constants to factory
settings, and automatically returns constant

no-00 setting to 01 .

If the GPD 333 is connected for 3-Wire control and this constant is
set to 08 ( 2-Wire control initialization ), the motor may run in
reverse direction WITHOUT A RUN COMMAND APPLIED.
Equipment damage or personal injury may result.

Constant

no-03 must be set for the proper motor voltage. Drive

leaves factory with this constant set for 230.0 or 460.0 volts.

CAUTION

Always ground the GPD 333 using ground terminal G ( E ). See
paragraph 1.4.2 "Grounding".

Never connect main circuit output terminals T1 ( U ), T2 ( V ) &
T3 ( W ) to AC main circuit power supply.

CAUTION

Do not perform a withstanding voltage test on any part of the
GPD 333. Equipment uses semi-conductors and is vulnerable to
high voltage.

The Control PC board employs CMOS ICs which are easily dam-
aged by static electricity. Use proper electrostatic discharge
(ESD) procedures when handling the Control PC board.

– i –

efesotomasyon.com - Yaskawa ac drive,servo motor

«
...
2
3
4
5
6
...
»

Содержание GPD 333


















































































Отзывы:

Нет отзывов

Похожие инструкции для GPD 333

Бренд: Lakeshore Страницы: 192

Бренд: QUAD Страницы: 16

Бренд: Lawler Страницы: 2

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: OBaby Страницы: 7

Бренд: Koer Страницы: 6

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды