Magnetek GPD 333 Скачать руководство пользователя страница 28

Страница: 28 / 81

1.6

START-UP WITHOUT DIGITAL OPERATOR

(2-Wire control; see Figure 1-5) (constant

no-01

set to 0000

[factory setting] )

ACTION

Freq. Ref. set at
zero; FWD RUN
and REV RUN
inputs open.
Apply Power.

Increase Freq.
Ref. input to
maximum.

Status Plate

DS1 DS2

(GREEN) ( RED )

BLINKING

Off

LIT

Off

LIT

Off

LIT

Off

(during decel)

BLINKING

Off

(when stopped)

DESCRIPTION

Ready for operation.

Close FWD RUN
or REV RUN
input; increase
Freq. Ref. until
motor rotates.

Open FWD RUN
or REV RUN
input.

Check that motor is rotating in
the correct direction. See Note 1.

Motor speed decreases under
GPD 333 control, at programmed
decel rate (constant

no–10

; fac-

tory setting = 10.0 seconds decel
time from 60Hz to 1.5Hz). Motor
then remains stopped.

GPD 333 output increases at pro-
grammed accel rate (constant

no–09

; factory setting = 10.0 sec-

onds accel time from 1.5Hz to
60Hz) to level commanded by fre-
quency reference input. Motor
speed increases accordingly.

NOTES:

If motor is not rotating in proper direction, stop motor and
turn off power to the GPD 333. Switch motor connections T1
(U) & T2 (V) at the GPD 333 to change direction.

efesotomasyon.com - Yaskawa ac drive,servo motor

Содержание GPD 333


















































































Результаты поиска

Содержание GPD 333

Отзывы:

Похожие инструкции для GPD 333

Бренды по названию

Популярные бренды

Magnetek GPD 333, Техническое руководство

Результаты поиска

Содержание GPD 333

Отзывы:

Похожие инструкции для GPD 333

Бренды по названию

Популярные бренды