MAGNATRAC RT1150 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 90

MAGNATRAC RT1150 Скачать руководство пользователя страница 25

BATTERY

Your Crawler has a 12 volt, negative-grounded
system with one battery.

BATTERY PRECAUTIONS

CAUTION:

Sulfuric acid in batteries is

a poison and could cause severe burns.
Avoid contact with skin, eyes, and
clothes. When you work around batter-

ies, protect eyes and face from battery fluid and
explosion.

CAUTION:

Keep flames and sparks

away from battery.

Do not use booster cables or adjust bat-

tery terminal connections unless you know the
correct procedure.

When you charge a battery or use a battery in a
closed space, be sure there is enough ventilation.
Keep batteries where children cannot reach them
with vent caps tight and level.

COLD WEATHER BATTERY SERVICE

During cold weather, attach a trickle charger to
your battery for ease of starting.

BATTERY STORAGE

If Crawler will be stored for more than 30 days, re-
move battery. Keep it fully charged.

BATTERY MAINTENANCE

1. Remove corrosion from terminals with a stiff,
non-metallic brush.

2. Maintain protective cover on “positive” (+) ter-
minal of battery.

3. Replace battery approx. every 3 years.

LOCATION & REMOVAL

Your battery is securely mounted inside the bat-
tery box shown below. Battery box cover is slot-
ted for easy access, and has a lockable bolt that
securely holds the cover in transit.

To Remove Cover:

1. Loosen lockable bolt and

nut. 2. Lift up. 3. slide cover forward.

To Remove Battery:

Your battery is fastened to

the inside of the battery box, by a “side” mounting
bracket and 2 long bolts.

1. Loosen (but do not remove) 2 nuts, securing
“side” bracket to the side of the battery.
2. Loosen and remove Carriage bolt & nut from
both (+) and (-) terminals. Do the (black) wire first,
and make sure to touch any metal with a wrench
when disconnecting the postive (+) red wire.
3. Lift battery out of battery box. Work in reverse
order when replacing with new battery.

25

Lockable Bolt

and Nut

Cover

Box

1. Loosen Bolt & Nut

2. Lift Up

3. Slide Forward

1

1

2

2

«
...
23
24
25
26
27
...
»

Содержание RT1150



























































































Отзывы:

Нет отзывов