MAGNATRAC RT1150 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 90

MAGNATRAC RT1150 Скачать руководство пользователя страница 18

5- DRIVE BELT, FUELS

& LUBRICANTS

BELT

DRIVE BELT

Your RT1150 is equipped with a

#004520 Oil &

Heat Resistant, Hi-Power II Double V Drive
Belt

. This drive belt powers your left & right hy-

drostatic transaxles, as well as your hydraulic at-
tachment pump.

FUELS

FUEL SPECIFICATIONS

Add fuel to fuel tank per engine manual specs.

Unleaded 86 octane or higher

is recc-

ommended per HONDA. Verify fuel shut-
off valve is in the open position.

FILLING FUEL TANK

The Fuel Tank is located underneath the hood, on
the engine.

Fuel Tank capacity is 0.61 US gallons.

Use unleaded gasoline per Engine Owner’s Man-
ual.

CAUTION:

Handle fuel carefully. Do

not fill fuel tank when the Engine is run-
ning. Do not smoke while you fill fuel
tank or work on fuel system.

STORING FUELS

Keep fuel in a container in a protected area.
Water and sediment must be removed before fuel
gets to the Engine. Do not depend on fuel filters
to remove water.

IMPORTANT:

Keep all dirt, scale, water, or other

foreign matter out of fuel.

LUBRICANTS

ENGINE OIL

Check enclosed Engine Owner’s Manual and
closely follow their recommendations.

10W30 is

recommended for general use.

TRANSAXLE OIL

Check enclosed Transaxle Manual and closely fol-
low their recommendations. Typically, an engine
oil with a minimum rating of 9.0cSt (55 SUS) at
230º F (110º C) and an API classification of SL is
recomended. A

20W50 engine oil has been se-

lected for use by the transaxle factory

and is

recomended for normal operating conditions.

HYDRAULIC ATTACHMENT OIL

Use a premium quality hydraulic oil with maximum
anti-wear properties, rust and oxidation treatment.
We use an

AW46 Hydraulic Oil

. (ISO 46). If op-

erated at exteme hot or cold temperatures, please
consult a local oil shop for an oil viscosity best
suited for your conditions.

GREASE

Use premium quality SAE Multi-Purpose Grease
in a grease gun, with a flexible “nose” to lubricate
grease zerks throughout the MAGNATRACS pivot
points. Recommended grease:

Multipurpose

NLGI 2 Grade Lithium Complex, ISO VG 220

.

REAR DRIVE CHAIN LUBRICATION

At a minimum...brush on

SAE 30 weight oil (non-

detergent)

on rear drive chains.

A more expen-

sive, but cleaner option is to use a spray lubricant,
such as:

non detergent aerosol Chain & Wire

Rope Lubricant. We use CRC® brand,
Grainger® Item #2F139.

Both of these methods

are acceptable lubrication options.

STORING LUBRICANTS

Store lubricants in clean containers in an area pro-
tected from dust, moisture, etc.

18

«
...
16
17
18
19
20
...
»

Содержание RT1150



























































































Отзывы:

Нет отзывов