-26-
2.5
Scope of supply
1x
Milling motor FM 1650 PV-LO
(9M0801)
1x
Operating manual
(170783)
1x
Open-ended spanner SW 22
(093012)
2.6
Use according to intended purpose
-
The milling motor is intended for permanent installation in portal systems of leading manufacturers with
Ø 43 mm collar.
-
The milling motor can be flanged directly to a portal system using six screws (M6 thread) according to the
specifications of the portal system (Fig. 4).
-
The milling motor is not designed for continuous industrial operation.
-
The milling motor is considered an incomplete machine. The milling motor may only be commissioned once it
has been determined that the portal system into which the milling motor is to be incorporated complies with
the provisions of the current and valid Machinery Directive. Please also note the corresponding warranty
conditions for the milling motor and any supplementary appliances.
2.7
Residual risks
Danger
Even if used in accordance with its intended purpose and despite conforming with the
safety instructions, residual risks caused by the intended use that can lead to health
consequences will always remain.
-
Breakage of the rotating tool.
-
Breakage of the tools and risk of the tools or parts of them being hurled away.
-
Touching live parts with the housing open and the mains plug not removed.
-
Hearing impairment when working for long periods without ear protectors.
-
Emission of hazardous or potentially explosive dusts (all types) during longer lasting operation without
extraction. Please note the safety data sheet of the material to be machined.
-
Cut injuries when changing tools.
-
Danger of burns when touching the housing if the maximum permissible material removal rate is continuously
exceeded (see page 28).
3
Safety instructions
Danger
Always observe the following safety instructions and the safety regulations applicable
in the respective country of use!
General instructions:
-
Children and adolescents must not operate this machine. This rule does not apply to young persons receiving
training and being supervised by an expert.
-
Never work without the guards of the portal system into which the power tool is inserted and that are prescribed
for each operation. Do not make any changes to the portal system and the milling motor that could compromise
safety.
-
Damaged cables or plugs must be immediately replaced. Replacement may only be carried out by MAFELL
or an authorised MAFELL service workshop in order to avoid safety hazards.
Содержание FM 1650 PV-LO
