Maco MULTI POWER Скачать руководство пользователя страница 77

Страница: 77 / 92

max.

100 kg

max.

150 kg

WINDOWS

· DOORS · SLIDING DOORS

Threshold Profine A075 and A076

Basic processing instructions

Maximum sash weight

Threshold application area

The possible application and the scope of the different versions of the Profine A075 and

A076 threshold can be found in the documents of the Profine GmbH company.

Threshold parts list

The list of all required parts (threshold, weather bars, gaskets, etc.) and all accessories

can be found in the documents of the Profine GmbH company.

Processing and assembly instructions for thresholds / profile system

The processing guidelines of Profine GmbH regarding the connection of thresholds and

profile system must be observed in a binding manner!

IMPORTANT!

The threshold with frame

must be packed along

the entire length.

The load must be carried

by the packer profile!

without load transfer device

with load transfer device

The application diagram applies to

MULTI POWER with a maximum sash

weight of 150 kg!
If a load transfer device is additionally

installed, the processing instructions for load

transfer devices contained within the MULTI

POWER timber and PVC assembly

instructions (Order No. 757808) must be

followed!

The application diagram applies

to MULTI POWER with a maximum

sash weight of 100 kg!

Содержание MULTI POWER





























































































Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды

Maco MULTI POWER, Инструкция по сборке

Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды