Maco MULTI POWER Скачать руководство пользователя страница 4

Страница: 4 / 92

WINDOWS

· DOORS · SLIDING DOORS

Important Information

Target audience

This documentation is intended exclusively for specialist companies and certified specialists.

The work-steps described here in may only be carried out by certified specialists.

Instructions for use

•

Unless otherwise indicated, measurements are made in millimetres.

•

Mount all hardware parts professionally as described in this manual and observe all safety

instructions.

•

All diagrams are only symbolic.

•

Further technical documents can be found in our online catalogue (TOM) at

extranet.maco.eu.

• This print document is constantly being revised and is available for download in the current

version at www.maco.eu.

•

Printing errors, mistakes and changes are reserved.

• Please send feedback or suggestions and ideas for improvements on our instructions by

email to: [email protected]

Material notes

• The hardware parts described in this guide are made of stainless steel or galvanised

passivated steel and sealed in accordance with DIN EN 12329. They must not be used in

environments with aggressive, corrosive air content.

•

Do not use acid-curing sealants, as these can lead to corrosion of the hardware parts.

• The window and casement door elements may only be surface-treated before the hardware

is installed. Any subsequent surface treatment may restrict the functionality of the hardware.

In this case, no warranty claims can be made against the hardware manufacturer.

Содержание MULTI POWER





























































































Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды

Maco MULTI POWER, Инструкция по сборке

Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды