Maco MULTI POWER Скачать руководство пользователя страница 27

Страница: 27 / 92

max.

110 kg

max.

150 kg

WINDOWS

· DOORS · SLIDING DOORS

Threshold

GRUNDMEIER „COMBI”

Basic processing instructions

Maximum sash weight

DANGER!

The threshold must be

packed along the entire

length in the hinge area.

The load must be carried

by the packer profile!

DANGER!

These assembly

instructions are only

valid for the Aluminium

version, not for the PVC

version!

without load transfer device

with load transfer device

Threshold application area

The possible application and the scope of the different versions of the "COMBI" threshold

can be found in the documents of the Grundmeier KG company.

Threshold parts list

The list of all required parts (threshold, threshold holders, gaskets, etc.) and all

accessories can be found in the documents of the Grundmeier KG company.

Processing and assembly instructions for

thresholds / profile system

The processing guidelines of the profile

manufacturer or system provider regarding

the connecting of the threshold and frame

profile or profile system must be observed in a

binding manner!

For the connecting element, only the

implementation shown here is

permitted!

The application diagram applies to

MULTI POWER with a maximum sash

weight of 150 kg!
If a load transfer device is additionally

installed, the processing instructions for load

transfer devices contained within the MULTI

POWER timber and PVC assembly

instructions (Order No. 757808) must be

followed!

The application diagram applies

to MULTI POWER with a maximum

sash weight of 110 kg!

Содержание MULTI POWER





























































































Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды

Maco MULTI POWER, Инструкция по сборке

Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды