Maco MULTI POWER Скачать руководство пользователя страница 18

Страница: 18 / 92

max.

110 kg

max.

150 kg

WINDOWS

· DOORS · SLIDING DOORS

TRANSIT threshold extendable with strip gasket

Basic processing instructions

Maximum sash weight

Threshold application area

The possible application and the application areas for the different versions of the

extendable TRANSIT threshold must be taken from the assembly instructions for the

extendable Transit threshold (Order No. 750097).

Threshold parts list

The list of all required parts (threshold, adjustment piece, cover profile, gasket, etc.) and

all accessories are subject to the assembly instructions for the Transit threshold (Order

No. 750097). These parts can also be found in the MACO Online Catalogue (TOM).

Processing and assembly instructions for thresholds / profile system

The processing guidelines of the profile manufacturer or system provider regarding the

connecting of the threshold and frame profile must be observed in a binding manner!

The general connection of the threshold and frame profile is subject to the assembly

instructions for the extendable Transit threshold (Order No. 750097).

DANGER!

The threshold must be

packed along the entire

length in the hinge area.

The load must be carried

by the packer profile!

without load transfer device

with load transfer device

The application diagram applies to

MULTI POWER with a maximum sash

weight of 150 kg!
If a load transfer device is additionally

installed, the processing instructions for load

transfer devices contained within the MULTI

POWER timber and PVC assembly

instructions (Order No. 757808) must be

followed!

The application diagram applies

to MULTI POWER with a maximum

sash weight of 110 kg!

Содержание MULTI POWER





























































































Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды

Maco MULTI POWER, Инструкция по сборке

Результаты поиска

Содержание MULTI POWER

Отзывы:

Бренды по названию

Популярные бренды