background image

 

 THESE DIMENSONS ARE APPROXIMATE.

REFER TO THE INSTRUCTIONS ON 

 THE

S.W.R. TO DETERMINE EXACT SETTINGS. THERE

 SEPARATEGAMMAADJUSTMENTS, 

TOR ADJUSTMENT, 2. SLIDER POSITION.

DO NOT MOVE BOTH AT THE SAME TIME. 

MOVE

THE CAPACITOR FIRST, THEN, IF NECESSARY MOVE
THE SLIDER, AND GO BACK TO THE CAPACITOR.

 -GAMMA STRAPS

(INSTALL FLUSH

AGAINST 

ELEMENT MOUNT)

S21, 

 

 O-24 x 

 SCRE

LK. WSHRS   SQ.

NUTS

S21, 

 N12

 O-24 x 

 SCREWS

LK. WSHRS 8 SQ.

 24 NUT

 

WASHER

GAMMA STRAPS

(SLIDER)

(CUSTOMER

FURNISHED)

 PLASTIC SHOULDER

WASHER

 FLATWASHER

 GO1 P GAMMA MATCH

FIGURE 4

GAMMA MATCH MOUNTING

Mount the gamma match (GO 

 to the driven element, using the gamma straps 

 

 and attaching

hardware as shown. Attach your 52 ohm coaxial cable to the connector (S42) and dress along boom and down the
mast. The gamma is shown pointing down   this is to let water out.

ADJUSTING THE STANDING WAVE RATIO 

Refer to Figure 4. The dimensions given are approximate and should be used as a starting point. * The gamma

match has 2 adjustments. First is the capacitor adjust and second is the slider adjust. Connect a SWR bridge coax
between your transmitter and the antenna and check the SWR. If adjustment is required, loosen the clamp on the
gamma match and the screws holding the slider (gamma straps 

 Next move the capacitor adjustment first

one direction, then the other until a minimum SWR reading is obtained. If SWR is not yet satisfactory, move the
slider out 2” away from the boom.

 reading has gone up move the slider back to the original position and then

2” towards the boom. Now readjust the capacitor for minimum SWR. You should now be able to determine which
direction to move the slider. Repeat the above procedure moving the slider in smaller increments until a satisfactory

SWR is obtained. Tighten all hardware. Disconnect the SWR bridge and reconnect your coaxial cable.

NOTE!

When assembling for vertical use, set antenna on a pole about 8 to 9 feet above the ground horizontally and

adjust 

SWR to 1.7. When you turn the antenna vertical and mount it on the tower, etc., the SWR will drop to 1.4

to 1.5. This is good; QUIT! Antenna results best if vertical antenna clears the top of the tower.

9

Содержание M107C












Отзывы: