background image

LIMITED WARRANTY

 

 

Motor Appliance Corporation (hereafter called MAC) warrants that each new and unused MAC Commercial Battery Charger manufactured is of good 

workmanship and is free from any known mechanical or electrical defect(s).  This warranty is contingent upon that (1) the product is installed and 

operated in accordance with generally accepted industrial standards and in accordance with the printed instructions provided by MAC, (2) the 

product is used under normal conditions for which designed, (3) the product is not subject to misuse, negligence or accident, and (4) the product 

received proper care, protection and maintenance under supervision of competent personnel.  This limited warranty is subject to the following 

provisions: 

 

WARRANTED PRODUCTS AND PARTS.  SERVICE LABOR COST IS NOT COVERED.  Subject to the exception listed below each MAC 

Commercial Battery Charger is warranted for a period of twenty-four (24) months from the date of manufacture.  The exceptions to 

this warranty are as follows: 

 

AC & DC Fuses and AC & DC power cables are not warranted unless found defective upon initial installation.  

This warranty does not apply to a charger used in a mine or in mining operations. 

Damage due to voltage surges, lightning, acid spills and customer abuse are not  

covered by this warranty. 

 

NON-TRANSFERABLE WARRANTY. This warranty is extended by MAC only to the original user (purchaser) of new equipment from MAC 

or one of its authorized selling organizations.  The products purchased under this agreement shall be used exclusively by the buyer.  

There shall be no third party or beneficiary to this warranty. 

 

REPAIR LIMITATIONS.  The existence of claimed defects in any product covered by this warranty is subject to MAC's factory inspection 

and judgement.  MAC's liability is limited to the repair and replacement of the defective product found by MAC or MAC's Authorized 

Service Centers.  Return defective product pre-paid to MAC, Industrial Drive, Blytheville, AR 72315.  Replacement and exchange parts 

will be warranted for the remainder of the original MAC Commercial Battery Charger Limited Warranty period or warranted for a 

period of ninety (90) days, whichever is greater. 

 

MAC and its authorized service centers shall not be liable for direct or indirect damages in excess of such repair of 

replacement.  In no event shall the purchaser be entitled to recover for contingent expenses resulting from but not 

limited to, telephone calls, telegrams, travel expenses, lodging, duties and taxes, labor, rental or replacement 

equipment, batteries, loss of business or profits or other commercial losses. 

 

CONTINUED USE OF DEFECTIVE PRODUCT.  The continued use of a MAC Commercial Battery Charger that is known to be defective 

VOIDS ALL WARRANTIES. 

 

REPAIRED OR MODIFIED EQUIPMENT.  Except as authorized in writing, the warranty specified does not cover any equipment that has 

been repaired by any party other than MAC or its authorized service centers.  Except as authorized in writing, this warranty does not 

cover any equipment that has been modified, mechanically or electrically, by any party other than MAC. 

 

WARRANTY EXPENSE LIMITATION.  MAC shall limit the warranty expenses for all chargers to be paid at a maximum of the original 

purchase price of the charger. 

 

EXCEPT AS STATED ABOVE, ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESSED OR IMPLIED, INCLUDING IMPLIED WARRANTIES OR 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND BUYER ASSUMES ALL RISK AND LIABILITY RESULTING FROM THE 

USE OF THE GOODS.  MAC NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR MAC ANY OTHER LIABILITY IN CONNECTION WITH THE 

SALE OR USE OF THE GOODS SOLD, AND THERE ARE NO ORAL AGREEMENTS OR WARRANTIES COLLATERAL TO OR AFFECTING THIS WRITTEN 

WARRANTY. 

 

MOTOR APPLIANCE CORPORATION     555 Spirit of St. Louis Blvd.     St. Louis, MO     March 1, 1996 

 

1900.10A 

 

 

 

Содержание SCR Series






















Отзывы: