35
electric dryer connection
Representation of the power supply cord.
GREEN
BLACK
RED
WHITE
Before proceeding, keep the following in mind:
t
t
Ideal connection
GND
L2
L1
N
FIGURE2
t
.
ELECTRICAL REQUIREMENTS
warning:
electrical connection instructions for gas dryers
warning:
TO REDUCE THE RISK OF FIRE,
ELECTRICAL SHOCK AND PERSONAL INJURY:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER
PLUG WITH THIS APPLIANCE.
The dryer must be electrically grounded in
accordance with local codes and regulations.
This dryer must be powered with 220V~, 60 Hz,
120 V~ 60 Hz, or 220V~, 50Hz to a properly grounded
branch circuit, protected by the circuit breakers or required
15 A time delay fuse. If the electrical installation does
not meet the specifications, call a licensed electrician.
make sure there is
proper grounding
before using.
To reduce the risk of electrical shock, this dryer has a
t
i
d
n
a
)
g
n
i
d
n
u
o
r
g
r
o
f
(
d
r
o
c
n
o
i
t
c
e
n
n
o
c
e
r
i
w
e
e
r
h
t
must be connected to the appropriate three wire
supply socket. Do not cut or remove
the ground
connector wire of this plug.
IF ALLOWED BY LOCAL CODES, AN
EXTERNAL GROUND CONNECTION (NOT
PROVIDED) MAY BE INSTALLED;
CONNECTING
IT TO THE GREEN GROUNDING SCREW
LOCATED ON THE BACK OF THE DRYER, AND
TO A METALLIC AND GROUNDED COLD
WATER PIPE OR TO ANY OTHER STIPULATED GROUND.
For your convenience, the dryer includes an electric
cordless plug so you can choose the type of power plug to
use acc ording to the socket you have at home. Once you
have unpacked the dryer, on the back you will find a black
wire that has four more different colored wires, as sho wn in
the following figure:
The red wire represents Line 1 (with voltage), the black wire
represents Line 2 (with voltage), the white wire represents
neutral (without voltage) and the green wire represents
ground; this wire is very important, as it could save your life
in case of electric shock.
Do not connect the electric dryer by yourself. Electric dryers
must be properly connected by a qualified electrician .
To avoid danger, do not use damage cord.
If the power supply cord is damaged, it
must be replaced by the manufacturer,
your service agent or qualified personnel.
Your electrical installation must have two lines with
voltage (line 1 and line 2), a neutral (w/o voltage) and a
ground. You must have a neutral line independent from
the grounding one. Otherwise yo ur dryer could be
damaged. The way to make sure you co mply with this
requirement is as follows:
At home, you have a socket similar to the one shown in
figure 2.
(Note: this type of socket is only an example of the
different 220 V
~
sockets for home electrical installation).
A multimeter is to be used to ensure the installation meets
with the specifications. This tool will be used to measure the
voltage between L1 (line 1) and N (neutral), which must be
120 V
~
;
and also between L2 (line 2) and N (neutral) . The
voltage between L1 (line 1) and L2 (line 2) is 120 V
~
. Once the
specifications are complied, you must proceed to choose a
plug. The plug you s elect must support 30 A, and be
specified to 250 V
~
.
Furthermore, your choice must fit your
home socket.
49
Содержание SMV630DEWWY00
