background image

7

OPERATION

1. BATTERY CHARGING

The battery is supplied partially charged. To 

ensure full capacity of the battery, completely 

charge the battery in the battery charger before 

A fully discharged battery pack will charge in 

about 50 minutes in a surrounding temperature 

between 32°F (0°C) and 104°F (40°C).
1) Charge the Lithium-Ion battery pack with the

correct charger.

2) Connect the charger to a power supply.
3) Align the raised ribs of the battery pack with

the slot in the charger.

4) Slide the battery pack onto the charger
5) The charger will communicate with the

battery pack to evaluate the condition of the

battery pack.

6) The POWER BAR LED lights will cycle from

right to left during charging. This is part of the

normal charging operation.

7) After charging is complete, the green LED

on the charger will come on and the POWER

BAR LED lights will go displayed when the

POWER BAR button is pressed while the

battery pack is on the charger.

8) The battery pack will fully charge if left on the

charger, but it will not overcharge.

       

WARNING:

 Do not charge below 0 degree 

or above 40 degree, battery may not  be 

charged or be fully charged.

Содержание DD-2050










































Отзывы: