background image

5

SAFETY RULES FOR CHARGER

       WARNING: 

To reduce the risk of electric 

shock or damage to the charger and battery, 

charge only those lithium-ion rechargeable 

charger’s label. Other types of batteries may 
burst, causing personal injury or damage.
1. Before using battery charger, read all

instructions and cautionary markings in

this manual and on the battery charger, the

battery and the product using the battery to

prevent misuse of the products and possible

injury or damage.

2. Do not use the charger outdoors or expose it

to wet or damp conditions. Water entering the

charger will increase the risk of electric shock.

3. Use of an attachment not recommended or

sold by the battery-charger manufacturer may

to persons.

4. Do not abuse the cord or charger. Never

use the cord to carry the charger. Do not pull

the charger cord to disconnect the plug from

receptacle. Damage to the cord or charger

could occur and create an electric shock

hazard. Replace damaged cords immediately.

5. Make sure that the cord is located so that it

will not be stepped on, tripped over, come in

contact with sharp edges or moving parts, or

otherwise subjected to damage or stress.This

will reduce the risk of accidental falls, which

could cause injury and damage to the cord,

which could then result in electric shock.

6. Keep cord and charger from heat to prevent

damage to housing or internal parts.

7. Do not allow gasoline, oils, petroleum-based

products, etc. to come in contact with plastic 

parts. These materials contain chemicals that can 

damage, weaken, or destroy plastic.
8. An extension cord should not be used unless

absolutely necessary. Use of an improper

electric shock. If an extension cord must be

used, make sure that:

The pins on plug of extension cord are the

same number, size and shape as those of the 

plug on charger.
    The cord is properly wired and in good 

electrical condition
9. Do not operate the charger with a damaged

cord or plug, which could cause shorting and

electric shock. If damaged, have the charger

repaired or replaced by an authorized service
technician at  

 Service Center.

10. Do not operate the charger if it has has

otherwise been damaged in any way. Take it
to an authorized service technician at

Service Center for an electrical check to

determine if the charger is in good working

order.

11. Do not disassemble the charger. Take it to

an authorized service technician at a

Service Center when service or repair is

required. Incorrect reassembly may result in a

12. Unplug the charger from the electrical

outlet before attempting any maintenance or

cleaning to reduce the risk of electric shock.

13. Disconnect charger from the power supply

when not in use. This will reduce the risk of

electric shock or damage to the charger if

metal items should fall into the opening. It

will also help prevent damage to the charger

during a power surge.

14. Risk of electric shock. Do not touch the

uninsulated portion of output connector or

uninsulated battery terminal.

Содержание DD-2050










































Отзывы: