M-system R7ML-RS4, Инструкция по эксплуатации

Страница: 3 / 10

R7ML-RS4
P. 3 / 10 EM-7805-C Rev.2
■
STATUS INDICATOR LED
ID COLOR FUNCTION
PWR Green Turns on when the internal 5V is supplied
normally.
RUN Green Turns on in normal communications
conditions.
ERR Red Turns on in no communication or setting
error.
SD Green Turns on when the module is transmitting.
RD Green Turns on when the module is receiving.
■
STATION ADDRESS
Station Address is selected between 60H and 7FH (Intel-
ligent I/O) in hexadecimal. (Certain numbers may not be
selectable depending on the master types. Refer to the in-
struction manual of the master unit.)
The left switch determines the MSD, while the right switch
does the LSD of the address.
(Factory setting: 60H)
Station Address Setting (LSD)
Station Address Setting (MSD)
89AB
C
D
EF0
123
45
67
89AB
C
D
EF0
123
45
67
■
MECHATROLINK MODE
Choose MECHATROLINK-I or -II, and the data size. Posi-
tions 2, 4 through 9 are unused.
(Factory setting: 1)
5
4
3
2
1
0
9
8
7
6
MECHATROLINK Setting
0 : MECHATROLINK-II (32-byte mode)
1 : MECHATROLINK-II (17-byte mode)
3 : MECHATROLINK-I (17-byte mode)
■
EXTENSION MODULE
Combinations with any extension module is selectable.
■
OPERATING MODE
(*) Factory setting
• Extension (SW1-1, 1-2)
SW1-1 SW1-2 Extension
OFF OFF No extension (*)
ON OFF Discrete input, 8 or 16 points
OFF ON Discrete output, 8 or 16 points
• Conversion rate (SW1-3)
SW1-3 Conversion rate
OFF 250 msec. (*)
ON 1 sec.
• Burnout (SW1-4)
SW1-4 Burnout
OFF Upscale (*)
ON Downscale
• RTD type (SW1-5, 1-6, 1-7, 1-8)
SW1-5 SW1-6 SW1-7 SW1-8 RTD type
OFF OFF OFF OFF Pt 100 (JIS ’97, IEC) (*)
ON OFF OFF OFF Pt 100 (JIS ’89)
OFF ON OFF OFF JPt 100 (JIS ’89)
ON ON OFF OFF Pt 50 (JIS ’81)
OFF OFF ON OFF Ni 100
ON OFF ON OFF Cu 10 @ 25°C
OFF OFF OFF ON Cu 50
ON ON ON ON PC Configurator setting
■
PC CONFIGURATOR JACK
Analog input modules are equipped with the PC Configura-
tor Jack.
The PC Configurator is used to set the following parameters
for each channel.
• Zero and span adjustments
• Scaling (factory default: engineering unit conversion (°C))
• Conversion rate (factory default: 500 msec.)
• Sensor type and range
Before starting programming, turn on the front SW1-5, 6, 7,
8. For more information about the programming using the
R7CON, please refer to the R7CON Users Manual.
■
POWER SUPPLY TERMINAL ASSIGNMENT
4
NC
5
NC
6
+24V
1
NC
2
NC
3
FG
7
0V
NO. ID FUNCTION, NOTES
1 NC ----
2 NC ----
3 FG FG
4 NC ----
5 NC ----
6 +24V Power input (24V DC)
7 0V Power input (0V)
■
INPUT TERMINAL ASSIGNMENT
10
INA0
11
INb0
12
INA1
1
NC
2
INB0
3
NC
13
INb1
4
INB1
14
NC
5
NC
15
INA2
6
NC
16
INb2
7
INB2
17
INA3
8
NC
9
INB3
18
INb3
NO. ID FUNCTION NO. ID FUNCTION
1 NC No connection 10 INA0 RTD 0-A
2 INB0 RTD 0-B 11 INb0 RTD 0-b
3 NC No connection 12 INA1 RTD 1-A
4 INB1 RTD 1-B 13 INb1 RTD 1-b
5 NC No connection 14 NC No connection
6 NC No connection 15 INA2 RTD 2-A
7 INB2 RTD 2-B 16 INb2 RTD 2-b
8 NC No connection 17 INA3 RTD 3-A
9 INB3 RTD 3-B 18 INb3 RTD 3-b
056 222 38 18 mailbox@sentronic.com www.sentronic.com
SENTRONIC
AG