English
Operating instructions / user’s manual Cooker Hoods
fi100417ATBOR
6
GB
the filter function and are not
grounds for
complaint
.
7.1 Changing the grease filter
Grease filters must occasionally be changed. The
following rules apply:
•
Change
paper grease filters
monthly
•
Change
paper grease filters with alarm
every
two months or when the colour of the surface
becomes visible through the mesh openings. This
filter is coloured on one side; after fitting, this
colouring must not be visible through the mesh
openings.
•
Foam grease filters
must be soaked once a
month in warm soapy water for 1 to 2 hours. Do
not wring out; repeat where required and replace
the filter by a new item after a maximum of 5-6
washes.
•
Metal grease filters
do not have to be replaced
when they are over-saturated but washed once a
month by hand or in a dishwasher (60°) (please do
not use a corrosive rinsing agent). Allow the filter
to dry thoroughly and carefully replace it in the
extractor hood.
Avoid using alkaline dishwasher cleaning
agents (ph value over 7).
•
Carbon filters
a)
Traditional carbon filters (normally round in
shape)
can be neither washer nor regenerated.
The charcoal filters have to be replaced regularly,
at least every 3 months or earlier, depending on
the cooking habits
b)
Washable and regeneratable carbon filters
(normally square in shape)
are to be washed
once a month in a dishwasher, using a standard
rinsing agent and with the intensive rinsing
program (at the highest temperature).
Washable and regeneratable carbon filters
absorb kitchen odours for a maximum of 3 years
when cleaned monthly. The filter should then be
replaced by a new item.
Washable and regeneratable carbon filters
should be washed separately to avoid food residue
deposits which can later cause unpleasant odours.
After washing, the washable and regeneratable
carbon filter must be reactivated. This is carried out
by drying the cleaned filter in an oven for 10
minutes at 100°C.
Read the package to see whether your carbon filter
is washable and regeneratable.
If the package carries no information, then it
contains a traditional, non-washable carbon filter.
Each time you change or wash a grease filter or
carbon filter, after removal clean all exposed lower
parts of the hood with a mild grease solvent.
For the daily cleaning of the outer pats of the hood
use a soft cloth moistened with alcohol or a mild
liquid cleaner. Never use an abrasive cleaner.
There is a risk of fire if the instructions for
cleaning the hood and the changing or cleaning of
the filters are not complied with.
8. Changing the lamps
When changing a lamp, make sure that the
new lamp does not have a higher wattage than that
of the original.
9. Fault – what to do if ...
The motor fails to function:
•
Is the plug properly inserted in the socket?
•
Is there a power supply failure?
•
Has a fuse blown?
The hood capacity is insufficient / operating
noise has increased:
•
Is the size of the exhaust air pipeline sufficient?
•
Is the exhaust air duct blocked?
•
The cross section of the air pipeline (from the
hood to the wall box incl.) should be 150 mm.
•
A smaller air pipeline cross-section can possibly
impair the motor power.
•
The air flow can be obstructed if the wall box is
fitted with a fly mesh.
If this is the case remove the fly mesh.
•
If the cover plate of the wall box has fixed, very
inclined louvres, you should remove the plate to
check whether this solves the problem.
•
Mount a cover plate with movable louvres in the
wall box, as this will least obstruct the air flow.
•
Is / are the filter(s) clean?
•
Was / were the carbon filter(s) installed more
than six months ago?
Then this/these should be changed.
•
Is the air taken from the kitchen being replaced
by sufficient fresh air, so that no partial vacuum is
being produced in the room?
The lighting fails to function:
•
Does the lamp need changing?
•
Has the lamp been properly fitted and seated in
the holder up to the stop?
