M. J. MAILLIS GROUP SIAT GTH 19, Руководство пользователя

Страница: 14 / 102

M.J. Maillis Group
ENGLISH -
4
Control components
- Tensioning button (fig. 1 – 1.1)
- Seal/Welding button (fig. 1 – 1.2)
- Opening lever (fig. 1 – 1.3)
- Control panel (fig. 3)
Switching on
Insert the battery as shown in (fig.2). The tool can be switched on by one of the following three actions:
- Push the tensioning button (1.1)
- Push the seal/welding button (1.2)
- Raise the opening lever of the tool (1.3)
Tool control panel description
The control panel is composed of: 7 segment 3 digit display (fig.3 - letter A, B, C), 3 LED (fig.3 – letter D, E, F) and two control buttons (fig.3 – letter G,
H).
The first digit of the display (fig.3 – letter A) indicates the tensioning force on a 1-9 scale. The second digit of the display (fig.3 – letter B) indicates the
seal/welding time on a 1-9 scale (see table below). The third digit (fig.3 – letter C) indicates the residual charge of the battery on a 1-9 scale.
The three LED displays 6 different tool operating modes of functioning. For more information see the section “Operating mode setting”.
The two buttons are used to scroll through the menu items, change the operating mode, tensioning force and seal/welding time settings.
Operation mode setting
The tool has three basic operating modes of functioning.
- Manual (fig.3 - 3.1) – The strap is tensioned by pressing the tensioning button (1.1).At the release of the button (1.1) the strap tensioning
stops. To obtain the set tensioning force, keep the tensing button pressed until the complete recovery of the strap and the consequent stop of
the motor. Start the seal/welding with the button (1.2). In this operating mode there is a full control on the strapping cycle.
- Semi-automatic (fig.3 – 3.2) - The strap is tensioned by pressing the tensioning button (1.1).At the release of the button (1.1) the strap
tensioning stops To obtain the set tensioning force, keep the tensing button pressed until the complete recovery of the strap and the
consequent stop of the motor. The seal/welding will start automatically when the set tensioning force is obtained. This operating mode
decreases the strapping time and guarantees very good strapping force repeatability.
- Automatic (fig.3 – 3.3) - The tensioning and the seal/welding of the strap is done automatically by pressing the tensioning button (1.1). In this
operating mode it is possible to stop the strapping cycle in any instant by pressing once again the tensioning button (1.1) or pressing the
seal/welding button (1.2) or raising the opening lever (1.3).
Soft tensioning – The soft tensioning can be applied on each of the basic operating modes: manual, semi-automatic and automatic. It consists in a
lower speed tensioning and longer acceleration times in order to obtain lower tensioning forces. The soft tensioning is recommended when the package
could be easily damaged and/or where a low tensioning force is requested. The soft tensioning is particularly suitable for a low thickness straps and/or
PP straps.
Approximate tensioning force values
1 2 3 4 5 6 7 8 9
Normal tensioning (N) 2200 2500 2700 3100 3400 3700 4000 4300 4500
Soft tensioning (N) 1000 1200 1300 1400 1600 1800 2100 2400 3100
Welding time table
1 2 3 4 5 6 7 8 9
Time (sec) 0,6 0,9 1,2 1,5 1,8 2,1 2,4 2,7 3
Settings
To enter the setting menu press both buttons, “SET” (fig.3 – letter G) and “+/-“ (fig.3 - letter H) at the same time.
The current operating mode setting starts to blink. Use the button “+/-“(fig.3 - letter H) to modify the setting of the operating mode scrolling through the 6
possible combinations. To scroll to the tensioning force value setting, press the button “SET” (fig.3 – letter G). The digit of the tensioning force starts to
blink. Use the button “+/-“(fig.3 - letter H) to set the desired value. To scroll to the seal/welding time value setting press the button, “SET” (fig.3 – letter
G). The digit of the seal/welding time setting starts to blink. Use the button “+/-“(fig.3 - letter H) to set the desired value.
To exit the setting menu and save the set values, ii any time, press the tensioning or seal/welding buttons or raise the opening lever.
To exit without saving, keep the control panel inactive for more than 10 seconds.
Strapping cycle
ATTENTION! Don’t press the tensioning or seal/welding buttons without strap in the tool.
If the tool works without strap, the feedwheel and the seal/welding plates could be damaged.The correct usage of the tool is the following:
Prepare the strap. Wrap the strap around the package (fig.4), keeping the end of the strap on the bottom and aligning both straps. Hold the strap in
your left hand.
Strap insertion. With your right hand, open the tool raising the opening lever (fig. 5). With your left hand, insert both straps keeping them well aligned.
Release the opening lever. Check the correct positioning/alignment of the straps before proceeding.
Start of the strapping cycle. Check the selected operating mode. Stay to the side to avoid possible lash of the strap due to excessive tensioning force
and consequent breaking of the strap. Press the tensioning button (1.1) see (fig.6).
In both manual and semi-automatic modes the tensioning of the strap stops if the tensioning button is released. In automatic mode, the strapping cycle
can be stopped at any moment by pressing the tensioning or seal/welding buttons or raising the opening lever.
ATTENTION! An excessive tensioning force could cause the break of the strap. The breaking of the strap could cause a serious injuries.
Seal/Welding of the strap. In manual mode, to start the seal/welding operation press the button (1.2) see (fig.7). In semi-automatic and automatic
modes the welding cycle will start automatically when the set tensioning force is obtained.
The seal/welding cycle includes the cutting of the strap.