Lynx L400PS, Руководство по эксплуатации и установке

Страница: 30 / 40

30
|
SEDONA CARE & USE/INSTALLATION
LEAK TESTING
Leak Test Procedure :
• Create a soapy solution of 1 part soap and 3 parts water.
• Confirm that all control knobs are in the off position.
• Turn on the fuel supply. For natural gas, turn the valve
handle 1/4 turn to align with the gas flow.
• For L.P., turn the cylinder valve knob counter clockwise
one full rotation.
• Apply the soap solution generously by paint brush or
squirt bottle on all connections and fittings.
• If bubbles appear to “grow” on any of the connections,
you have a gas leak. IMMEDIATELY turn off the gas supply.
Fixing a Gas Leak
• Shut off the gas supply
• Turn all grill controls to the “ON” position to purge
the grill of any gas build-up, then turn the controls
back “OFF”.
• Wash off the soapy solution with cold water and dry.
• Tighten the loose joint, or replace the faulty part with
manufacturer-recommended replacement parts.
• DO NOT attempt to repair the L.P. cylinder valve if it is
damaged. The only way to safely resolve a damaged
cylinder is to REPLACE IT.
• Repeat the leak test to ensure that no leaks are present.
LOW HEAT BURNER ADJUSTMENT
FOR MAIN STAINLESS STEEL AND PROSEAR™
BURNERS ONLY!
DO NOT ADJUST THE ROTISSERIE BURNER.
The main burners and side burners on your grill feature an
adjustable low setting.
Fluctuations in gas pressure, gas conversion and even in the
quality of the gas itself may affect burner performance at the
“LOW” setting. It could be either too high or too low.
To adjust the burner low setting:
• Make sure the grill is cool.
• Remove the cooking grates
and briquette trays so you can
see the flames while adjusting
the burners.
• Light the burner and allow it to
preheat on high for 3 minutes.
• Turn the burner to “LO”.
• Pull off the control knob.
• While holding the valve shaft with pliers as shown insert a
small flat screwdriver into the center shaft and adjust the
flame’s low setting.
The proper setting is where the flame is stable at its low-
est setting. A slight flutter will be present in the crossover
portion of the front of the burner before the burner itself
becomes weak.
The factory setting for propane gas is ½ to ¾ turn from the
very bottom of the adjustment. The setting for natural gas
is 1-½ to 1-¾ from the bottom. After the low settings are
proper, turn all burners to high for visual inspection.
BURNER FLAME/AIR SHUTTER ADJUSTMENT
The amount of air that enters a burner is controlled by the
air shutter
.
Each grill burner is tested and adjusted at the factory prior
to shipment. However, fluctuations in gas pressure, gas
conversion and even in the quality of the gas itself may
make it necessary to adjust the burner.
The flames of the main burners should be visually checked.
Flames should be blue and stable with slight yellow tips.
The bright-blue core should be about 3/8 inch high with a
total flame height of about 1 1/2 inches.
The flames should burn
quietly. (no “torch”
sounds) and they should
not “lift” up from the
burner.
If your flames do not match those indicated in the photo,
ensure that the air shutter and burner ports are free and
FINAL CHECKS
Clockwise will lower the flame
setting, counterclockwise will
raise it.
DANGER
TO PREVENT FIRE OR EXPLOSION HAZARD, DO
NOT SMOKE OR ALLOW ANY POTENTIAL SOURCE
OF IGNITION (SPARKS, ELECTRICAL ARCING, ETC)
IN THE AREA WHILE PERFORMING A LEAK TEST.
LEAK TESTS SHOULD BE CONDUCTED OUT-
DOORS ONLY. NEVER CONDUCT A LEAK TEST
USING FIRE OR FLAME.