background image

 

Input Module 

LOW 

The control has shelving response that giving 15dB 
of boost or Cut at 80Hz. Adding warmth to vocals or 
extra punch to guitars. drums and synths but turn 
to the right, turn to the left to reduce stage rumble, 
hum or to improve a mushy sound.   

6. AUX l 

This rotary fader sends out the channel signal to 
auxiliary bus 1. The signal is ere-fader So that the 
aux send  10 be  independent  of the fader: this  is 
suitable for feedback or monitor.   

AUX 2 

This rotary fader sends out the channel signal Io 
auxiliary bus 2. The signal is pre-fader so that the 
aux  send  to  be  independent  of  the  fader,  this  is 
suitable for feedback or monitor.   

7. EFF 

This  rotary  fader  feeds  the  channel  signal  to  the 
external effect the signal is post fader. This is very 
helpful  for  simultaneously  adjust  the  level  of  the 
processed signal.   

8. PAN 

This rotary control determined the assignment of 
signal forth the channel to left and right or 1 and 2 
groups. When the pan pot is set centrally signal is 
sent  equally  to  all  selected  groups  and  master. 
Turning  the  control  anticlockwise  send  relatively 
more  signal  to  the  left  master  and  to  the  SUB1 
Turning  the  pot  clockwise  sends  relatively  more 
signal to the right master and to SUB2. The 
pan pot may thus be used to adjust the position of 
signals in the stereo image.   

9. PEAK 

This  red  LED  (light  emitting  diode)  illuminates 
when  the  channel  approaches  an  overload 
situation.  the  LED  is  activated    3dB  before  the 
onset of clipping (distort). The input GAIN control 
should be adjusted So that the LED does not flash 
except on the highest level. brief transients. Using 
excessive  amounts  of  boots  on  the  channel 
equalizer may cause distortion on the channel

if 

this happens turn the input    GAIN control down.   

 
 
 
 

Содержание H-F08/2

















Отзывы: