LYINTL H-F08/2 Скачать руководство пользователя страница 10

Страница: 10 / 16

Output Connectors

37. BALANCED OUTPUT (MAIN L/R)

These sockets send line level signals from the mixer to external devices (for example

：

EQ or power amplifier).
L/R IACK UNBALANCEDD OUTPUT
These are jacks to send the finally mixed outputs to the other appliance (amplifier or
EQ).

38. SUB1 SUB2 OUT

The terminal to be output with the volume control against inputting signal into SUB l-2
board.

39. AUX1 AUX2 OUT

This socket sends out the signals from aux bus.

40. CTRLRM L/R

This jack is to be connected with the input jack of monitor amplifier when using
separate monitor amplifier.

41. AUX IN

This jack is to be connected with various external auxiliary signal.

42. PHONES JACK

This is used for monitoring the master signal and individually monitoring each channel
with PEL/AFL switch.

43. EFFECT SENG

This is used for adjusting volume of echo sound when sending echo sound to send jack

44. RETURN

This is used for adjusting frequency of echo repeat. Since too much echo repeat may
caused a howl. Please adjust frequency properly.

45. RECORD PIN JACK

This jack is to be connected with cassette deck when recording the mixed output.

46. PLAY PIN JACK

This jack is to be connected with cassette deck when playing back.

Power

Содержание H-F08/2

















Результаты поиска

Содержание H-F08/2

Отзывы:

Похожие инструкции для H-F08/2

Бренды по названию

Популярные бренды

LYINTL H-F08/2, Руководство пользователя

Результаты поиска

Содержание H-F08/2

Отзывы:

Похожие инструкции для H-F08/2

Бренды по названию

Популярные бренды