background image

17 | 

P a g e

 

 

ATTACH THE INSTALLATION BRACKETS  

 
Bracket spacing is the same for both inside and outside mounts. Two installation 
brackets are positioned on mounting surface so that their centrelines will be 
located 50mm from the ends of the headrail. If more than two brackets are 
required, additional brackets are spaced evenly between them. Measure and 
mark all bracket centrelines on the mounting surface.  
 
On the headrail of shadings over 915mm wide, the centrelines of the limit stops 
should be located 140mm from the ends of the headrail. On shadings 915mm or 
less in width, the limit stops should be located near the centre of the headrail.  

 

 
 
 
 
 
 
 
 
 
 
 
 
Should an obstruction prevent the end installation brackets from 
being mounted at the 50mm location, the brackets can be 
moved further from the ends of the headrail, to a maximum 
distance of 125mm. If the final location of the bracket 
centrelines is 100mm or more from the ends of the headrail, the 
limit stops must be moved. Reposition the limit stops so that their 
centrelines are 50mm from the ends of the headrail. The 
installation bracket has a tab on the bottom to prevent the 
fabric from snagging on the bracket. Do not break off the tab 
unless it interferes with bracket attachment. To remove the tab, 
simply twist it off with your fingers. 

 

INSIDE MOUNT APPLICATIONS  

 
To inside mount a Silhouette Shading, attach the tops of the installation brackets 
to the top sill of the window opening. The flat surface of the sill must be at least 
22mm deep. To fully recess the headrail assembly, the flat surface must be at 
least 73mm deep. Add to these minimum depth requirements the dimension of 
any obstruction to the bottom rail, such as a window crank or handle.  
Two  screws  are  used  to  attach  each  bracket.  Position  the  brackets  on  the 
centrelines you marked and then attach them with the appropriate fasteners. Be 
sure their front edges are aligned 

 
 
 

Содержание Silhouette Shades
























Отзывы: