manualshive.com logo in svg

Luna 20439-0108, Руководство пользователя, Страница: 27 / 67

Поделиться
Скачать
Luna 20439-0108 Скачать руководство пользователя страница 27

26

Fig. 17

Fig. 18

Fig. 19

Fig. 15

Fig. 16

6.2 Mounting the raving knife

The supplied raving knife must always be used. Disconnect saw from 
power source, unplug! The raving knife (F, Fig 15) is clamped with 1 nut
(U).

Adjust the space between sawblade teeth and raving knife to be 2 to 5mm.
Well tighten the locking nut (U).

6.3 Mounting the saw guard

The saw guard must always be used. Attach the saw guard (A, Fig 16) to
the raving knife (F) with 1 carriage bolt, washer and wing nut.

The saw guard must be lowered to the work piece to minimise the amount
of exposed teeth.

6.4 Rising and tilting of sawblade

Setup adjustments of the sawblade shall never be performed when the
machine is running. Use the front handle (I, Fig 1)to raise the sawblade.
Use the tilting handle (H, Fig 1) to tilt the sawblade. Tighten knob to lock
in place. Start the machine with care.

6.5 Rip fence setup

Rip fence setup shall never be performed when the machine is running.
Use 2 bots and wing nuts (W, Fig 17) to attach the aluminium profile (G)
to the rip fence body. 

Note:

The rip fence profile can be placed flat and adjusted in length.
-Use in upright position (Fig 17) for cutting wide stock:
-The cutting of small workpieces (width less than 120 mm) and tilted cuts
shall only be performed with the rip fence profile placed flat (Fig 18).

Start the machine with care.

6.6 Adjusting 90°stop

The positive stop is adjusted at the factory. If out of alignment: Disconnect
saw from the power source, unplug. Readjust the positive 90° stop.

6.7 Adjusting sawblade parallel

The sawblade is adjusted parallel to the machine table at the factory. If out
of alignment: Disconnect saw from the power source, unplug. Loosen the
screws on the tabletop (V, Fig 19) and readjust saw unit.

7. MAINTENANCE AND INSPECTION

General notes:
Maintenance, cleaning and repair work may only be carried out after
the machine is protected against accidental starting by pulling the
mains plug.

Repair and maintenance work on the electrical system may only be carried
out by a qualified electrician. Consult a qualified repair shop if a malfunc-
tion or damage occurs to this tool, including sawblades and guards.

Cleaning:

Clean the machine regularly. Inspect the proper function of the dust ex-
traction daily. Keep the inside of the cabinet clear of sawdust and wood
chips. All protective and safety devices must be re-attached immediately
after completed cleaning, repair and maintenance work. Defective safety
devices must be replaced immediately.

Saw blades:

The servicing of saw blades should only be performed by a trained person.
Defective safety devices must be replaced immediately. Check saw blades
regularly for faults. Replace a defective sawblades immediately.

Motor Break:

The motor break works electromechanically (break motor). If breaking ti-
me should exceed 10 seconds, the motor break assembly needs to be repla-
ced. Contact your LUNA service station immediately.

8. TROUBLE SHOOTING

Motor doesn’t start

*No electricitycheck mains and fuse.
*Defective switch, motor or cordconsult an electrician.

Machine vibrates excessively

*Stand on uneven flooradjust stand for even support.
*dust on saw flangesclean saw arbor and flanges.
*defective sawblade - replace sawblade immediately

Cut is not accurately square

*90° stop not adjusted correctlycheck with square and adjust stop.

Содержание 20439-0108




































































Отзывы:

Нет отзывов