manualshive.com logo in svg

Luna 20439-0108, Руководство пользователя, Страница: 26 / 67

Поделиться
Скачать
Luna 20439-0108 Скачать руководство пользователя страница 26

25

Fig. 12

Fig. 10

Fig. 11

Fig. 13

Fig. 14

Install wheels:

Attach the wheels (X, Fig 11) with 4 bolts and nuts.

4.3 Dust connection

Before initial operation, the machine must be connected to a dust extrac-
tor. The suction should switch on automatically when the saw is switched
on. Attach the connecting hose to the saw guard and the Y-piece A 100mm
dust collection hose can be connected.

4.4 Mains connection

Mains connection and any extension cords used must comply with appli-
cable regulations. The mains voltage must comply with the information on
the machine licence plate. The mains connection must have a 16A surge-
proof fuse. Only use connection cables marked H07RN-F. Connections
and repairs to the electrical equipment may only be carried out by qualifi-
ed electricians.

4.5 Starting operation

You can start the machine with the green ON button. The red OFF-button
on the main switch (C, Fig 1) stops the machine.

5. MACHINE OPERATION

Correct working position:

In front of the machine standing out of the line of cutting (danger zone). 

Work piece handling:

Hands placed flat on the work piece outside the cutting area. Feed the
work piece towards the saw blade in the direction of the saw line. Push the
work piece steadily forward; complete the cut as a single movement.
Support long and wide workpieces with helping roller stands.

Operating hints:

Always observe the safety instructions and adhere to the current regula-
tions. Ensure that the saw blade protective cover is in the correct position
before you start sawing. The cutting blade must first reach the maximum
rpm before cutting may begin.

Attention:

The condition of the blade should be checked before each machining pro-
cess. Work only with a sharp and flawless sawblade. Never use a sawblade
rated with a blade speed lower than the machine. Use a suitable wedge to
preven  round timber from turning under the pressure of the cut Use sui-
table table extensions and supporting aids for difficult to handle workpie-
ces. Always hold and guide the workpieces safely during machining. Do
not perform any operation freehand. Do not perform any grooving, teno-
ning or splitting operations on this machine. When ripping narrow workpi-
eces (width less than 120 mm) use a pushstick (Fig 12) or push-wood.

Make sure that small cut off workpieces will not be caught and thrown
away by the rising saw blade teeth. Remove cut and jammed workpieces
only when motor is turned off and the machine is at a complete standstill.
Pay particular attention on reducing the risk of kickback. The supplied 
raving knife must always be used. Inspect for correct adjustments.

For the authorized use of the machine observe the appendix A “safe
operation“ (on the last pages of this operating manual) (on the last 
pages of this operating manual)

A.1.: Ripping
A.2.: Ripping of narrow stock
A.3.: Crosscutting on rip fence
A.4.: Mitre cutting
A.5.: Ripping of big board

6. SETUP AND ADJUSTMENTS

General note:

Setup and adjustment work may only be carried out after the machine is
protected against accidental starting by pulling the mains plug.

6.1 Changing sawblade

The sawblade has to meet the technical specification. Use only sawblades
according to EN 847-1.  Check sawblade for flaws (cracks, broken teeth,
bending) before installation. Do not use faulty sawblades. The sawblade
teeth must point in cutting direction (down). Always wear suitable gloves
when handling sawblades.

WARNING:

When installing or changing saw blade, always disconnect

saw from power source, unplug! Remove the saw guard (A, Fig 1) and 
table insert (B). Raise sawblade fully. Loosen the arbor nut while stopping
the arbor against rotation with the supplied tools (S, T, Fig 13)

Attention: left hand thread. Remove the arbor nut (R, Fig 14 and flange
(Q).

Place saw blade(P) on arbor shaft making sure teeth point down at the
front of the saw. Reinstall flange and arbor nut and securely tighten.
Order for installation:
-adjusting washer (N)
-centring flange (O)
-saw blade (P)
-tightening flange (Q)
-left handed nut (R)
Reinstall the table insert and the saw guard.

Содержание 20439-0108




































































Отзывы:

Нет отзывов