How to Learn a Keyfob
-
hold SEL until it shows "n1" on display
-
press UP repeatedly until it increments to "n4" (i.e. Menu Level 4 selected)
-
press SEL to see "LE" on display (Learn Keyfob),
after 2 seconds starts flashing " 0"
-
press UP to increment it to value " 1" (i.e. "this operation is chosen")
-
press & hold MEM button until down
-
scores change to up
-
scores,
release MEM button, Learning has been started
-
press any button on Keyfob,
quick flashing of the LED on Keyfob indicates "Learned successfully".
Learning ends when (what happens first):
-
a transmission from Genesis
-
Keyfob is received;
if it is a known Keyfob (one of already Learned ones), then Learning just stops;
if it is a new Keyfob, then this new Keyfob is Learned and Learning stops;
if it is a new Keyfob but memory is full, then Learning just stops;
a timeout 30s passed (and no Keyfob received), then Learning just stops.
How to Erase ALL Learned Keyfobs
-
hold SEL until it shows "n1" on display
-
press UP repeatedly until it increments to "n4" (i.e. Menu Level 4 selected)
-
press SEL to see "Er" on display (Erase ALL Learned Keyfobs),
after 2 seconds starts flashing " 0"
-
press UP to increment it to value " 1" (i.e. "this operation is chosen")
-
press & hold MEM button until down
-
scores change to up
-
scores,
release MEM button, ALL Learned Keyfobs have been deleted.
How to restore Default Settings
-
hold SEL until it shows "n1" on display
-
press UP repeatedly until it increments to "n4" (i.e. Menu Level 4 selected)
-
press SEL to see "dS" on display (Default Settings),
after 2 seconds starts flashing " 0"
-
press UP to increment it to value " 1" (i.e. "this operation is chosen")
-
press & hold MEM button until down
-
scores change to up
-
scores,
release MEM button, ALL Menu Parameters have been deleted,
restarts with default settings (as brand new device from factory).
Notes
Note 1: Parameter "Unit" specifies PIR that is supposed to be mapped to relay A1.
It is the lowest PIR index processed by this Receiver.
The highest PIR index processed depends on number of relays available
(i.e. whether expansion module is fitted or not) and also on Configuration
of relay outputs, i.e. parameter "Configuration".
LGMRU4X4.v2 Masthead Relay Unit Installation Handbook.
Page 12
LGMRU4X4.v2 Masthead Relay Unit Installation Handbook.
Page 5
Features.
8 channels
(1..8) = 8 8 LED indicators
Can be configured as 4 alarm and 4 tamper relays (mode 2)
or 8 alarm relays only (mode 1)
Expansion module LGREM4x4.v2
Provides an extra 8 channels (9..16)
8 8 LED indicators
Can be configured as 4 alarm and 4 tamper relays (mode 2)
or 8 alarm relays only (mode 1)
2 global outputs
AUX_X,Y = 2 2 LED indicators
These two outputs can be programmed as follows
Either or both as grouped tampers
Either or both as grouped alarms
Either or both a keyfob Controlled outputs
Either can output missing call in (detector failed to call in)
ARM/DISARM
state can be controlled via external input INHIBIT or via LGKF4 Keyfobs
Possible control options are:
0 .. no ARM/DISARM control (ALARM relays always work on Detections)
1 .. ARM/DISARM control enabled, via Keyfobs
2 .. ARM/DISARM control enabled, via input INHIBIT
3 .. ARM/DISARM control enabled, via K also INHIBIT (INHIBIT has priority)
Keyfob control.
All Learned Keyfobs have the same function and are mutually
interchangeable
Functions of individual buttons:
top
-
left ........... ARM ALARM relays work on Detections
top
-
right ..........DISARM ALARM relays do NOT work on Detections
bottom
-
left ......KC_ON (Keyfob Controlled)
bottom
-
right ....KC_OFF
Any of the 2 global AUX relays can be configured to respond to this command.
Possible uses are gate opening and lighting control as well as many more.
Relay contact time.
Adjustable from 250ms to 39 minutes
Relay Configuration.
The user can configure the organization of the relays in the following ways
1 .. all channels are ALARMS only (MODE_1)
2 .. pairs of ALARM+TAMPER (MODE_2)
3 .. main
-
board gives 8 ALARM o plug
-
on module gives 8 TAMPER outputs
