Luminance Brands kathy ireland home CF835AP00 Скачать руководство пользователя страница 2

2

  

ETL Model No.: CF835

Safety Instructions

TO REDUCE THE RISK OF FIRE, ELECTRICAL 

SHOCK, OR INJURY TO PERSONS, OBSERVE THE 

FOLLOWING:

a. Use this unit only in a manner intended by the 

manufacturer.  If you have questions, contact the 

manufacturer.

b. Before servicing or cleaning unit, switch power 

off at service panel and lock service panel 

disconnecting means to prevent power from 

being switched on accidentally. When the service 

disconnecting means cannot be locked, securely 

fasten a warning device, such as a tag, to the 

service panel.

 

WARNING

!

Additional Safety Instructions for Installation

1.  To avoid possible shock, be sure electricity is turned 

off at the main fuse box or circuit breaker panel before 

wiring, and do not operate fan without blades.

2. All wiring must be in accordance with the National 

Electrical Code “ANSI/NFPA 70-2017” and Local 

Electrical Codes. Use the National Electrical Code 

if Local Codes do not exist. The ceiling fan must be 

grounded as a precaution against possible electrical 

shock. Electrical installation should be made or 

approved by a licensed electrician.

3. The outlet box and joist must be securely mounted 

and capable of reliably supporting at least 50 pounds. 

Use only U.L. outlet boxes listed as “Acceptable for 

Fan Support of 22.7 kg. (50 lbs.) or less”, and use 

the mounting screws provided with the outlet box. 

Most outlet boxes commonly used for support of light 

fixtures are not acceptable for fan support and may 

need to be replaced. Consult a qualified electrician 

if in doubt.

4. The downrod furnished with the fan provides the 

minimum recommended floor to fan blade clearance 

for an 8 foot ceiling.

5. Follow the recommended instructions for the proper 

method of wiring your ceiling fan. If you do not know 

enough about electrical wiring, have your fan installed 

by a licensed electrician.

NOTE: 

All set screws must be checked and re-tightened 

where necessary before installation.

1. Read your owner’s manual carefully and keep it for 

future reference.

2. Be careful of the fan and blades when cleaning, 

painting, or working near the fan. Always turn off the 

power to the ceiling fan before servicing.

3.  Do not put anything into the fan blades while they are 

turning.

4. Do not operate reversing switch until fan blades have 

come to a complete stop.

READ AND SAVE THESE INSTRUCTIONS

Table of Contents

Section Page

Safety Instructions    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

1 . Unpacking Instructions    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3-4

2 . Electrical Requirements   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4

3 . Removal of the Hanger Bracket      .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

4 . Installing the Hanger Ball/Downrod Assembly

 (Standard)

  6-7

5 . Installing the Ceiling Cover on the Fan Motor Housing

       

 (Close-to-Ceiling) 

    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .8-9

6 . How to Hang Your Ceiling Fan     .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .10-11

7 . Hanging the Ceiling Fan

 (Standard)

     .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11

8 . Hanging the Ceiling Fan

 (Close-to-Ceiling)

      .  .  .  .  .  .  .  .  .  .  . 12

9 . How to Wire Your Ceiling Fan     .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .13-14

10 . Installing the Ceiling Cover   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 15

Section Page

11 . Installing the Fan Blades   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 16

12 . Installing the Light Fitter Assembly & Shade  .  .  .  .  .  .  .17-20

13 . Using Your Ceiling Fan   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 21

14 . No Light Installation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 22

15 . Maintenance   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23

16 . Accessories   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23

17 . Energy Efficient Use of Ceiling Fans  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23

18 . Repair Parts    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .24-25

19 . Troubleshooting  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 26

Ceiling Fan Limited Warranty    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 27

Spanish  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29

To reduce the risk of electrical shock, this fan must be 

installed with an isolating wall switch.

This product is designed to use only those parts 

supplied with this product and/or any accessories 

designated specifically for use this product 

by Luminance Brands. Substitution of parts or 

accessories not designated for use with this product 

by Luminance Brands could result in personal injury or 

property damage.

To reduce the risk of personal injury, do not bend 

the blade flange when installing the blade flanges, 

balancing the blades or cleaning the fan. Do not insert 

foreign objects in between rotating fan blades.

 

WARNING

!

To reduce the risk of injury, install the fan so that the 

blades are at least 7 ft. (2.1m) above the floor.

 

CAUTION

!

Содержание kathy ireland home CF835AP00

























































Отзывы: