background image

Operating Manual CHM 15k 

 

R13 / 07-2019 

Safety... 

 

1.1  Symbols used 

 
 

 

Remarks for the smooth use of the equipment 

 

 

Required action step 

 

Safety

...

 

2.1  Standards and Directives 

The device is designed according to the recognized rules of technology and safety and is manufactured 
in series unchanged. The applied rules are listed in the currently valid declaration of conformity. 
Declarations of conformity can be downloaded from our homepage: 
 

https://www.lufft.com/products/cloud-height-snow-depth-sensors-288/ceilometer-chm-15k-nimbus-2300/ 

 

2.2  Safety instructions for the laser system 

The CHM 15k Ceilometer is classified as a Class 1M laser product according to IEC 60825-1:2014-06. It 
complies with 21 CFR 1040.10 except for deviations pursuant to Laser Notice No. 50, dated June 24, 
2007. The sensor emits a beam of invisible laser radiation (1064 nm) with small divergence (< 0.5 mrad) 
and a beam diameter of 90 mm. A warning label is attached to the front of the instrument (see 2.6). Class 
1M radiation  is regarded safe except when viewed with telescope optics. The instrument may only  be 
operated in a protected outside area. The following precautions must be taken when operating the sensor: 

 

Never view the laser beam with optical instruments, especially binoculars 

 

Avoid looking directly into the laser beam 

 

Do not operate the instrument with the inner sensor door open 

 

Do not operate the sensor horizontally (maximum tilt angle 20°) 

 

Keep the beam path free of reflecting materials 

 
The  laser  radiation  emitted  by  the  sensor  is  generated  by  an  embedded  Class  3B  laser.  Even  short 
exposure to Class 3B laser radiation can lead to injuries to the eye and skin. Maintenance and service of 
the  sensor  may  only  be  carried  out  by  trained  personnel.  Under  no  circumstances  may  the  laser  be 
removed from the measuring unit or any protective covers removed! 
 

2.3  Requirements for the personnel 

 

The  CHM 15k  may  only  be  installed  and  commissioned  by  trained  personnel  who  have 

received instructions in safety-related matters. Electrical connection of the device may only 

be carried out by a qualified electrician. 

 

Maintenance and adjustment work on the CHM 15k may only be carried out by the service 

staff  of  G. 

Lufft  GmbH  or  by  the  customer’s  authorized  and  trained  personnel.  All 

maintenance work requires a technical qualification in electrical safety. 

 

Every  person  assigned  to  install  and  commission  the  CHM 15k  must  have  read  and 

understood the complete user manual. 

 

During all work on the equipment, personnel must not be overtired and must not be under 

the  influence  of  alcohol,  medicines  or  intoxicants.  The  personnel  must  have  no  physical 

limitations that temporarily or permanently restrict their attention and judgment. 

 

2.4  Safety instructions for transport, installation, commissioning and cleaning 

 

The  CHM 15k  may  only  be  loaded  and  transported  in  the  packed  condition  and  in  the 

transport position (see Figure 5) using suitable lifting gear and transport equipment. 

 

Inside  the  shipping  container / 

truck  the  CHM 15k  must  be  adequately  protected  against 

slipping, shock, or other mechanical impacts, e. g. by using straps. 

Содержание CHM 15k










































































Отзывы: