LUDLUM 2363 Скачать руководство пользователя страница 9

Страница: 9 / 47

Model 2363

Technical Manual

Section 2

Ludlum Measurements, Inc.

Page 2-3

January 2015

Operating the Instrument

Connect a detector to the instrument if you have not already done so. Obtain

a meter reading from a check source or calibrated source, if available. Verify
that the reading falls within the expected range. Remove the source. If a

radiation source is available, increase the meter count to exceed the alarm
threshold. Both the appropriate alarm lamp and audio alarm signal should

activate.

Depress the

RESET

toggle switch. The meter needle should drive to zero, and

the alarm circuit should de-energize, shutting off both visual and audible
alarms.

Proceed with use.

Principle of Operation

The detected neutron count rate is displayed by selecting the

position on

the three-position

toggle switch. Similarly, the sum of the neutron

and gamma count rate or the gamma count rate only is displayed by selecting
the appropriate

position. The digital display will show a direct

reading in dose rate. Multiply the reading on the analog rate meter by the range
multiplier position.

The

RESET

toggle switch position resets the meter pointer to zero and

deactivates any current alarm. The current integrated dose is displayed on the
digital meter dial by selecting the

INTEGRATED DOSE

(

)

position.

Note:

The accumulated integrated dose may be reset by pressing the

ID toggle switch while turning the instrument

Содержание 2363
















































Результаты поиска

Содержание 2363

Отзывы:

Похожие инструкции для 2363

Бренды по названию

Популярные бренды

LUDLUM 2363, Руководство пользователя

Результаты поиска

Содержание 2363

Отзывы:

Похожие инструкции для 2363

Бренды по названию

Популярные бренды