LSIS SV-iS7 CANopen Скачать руководство пользователя страница 34

Страница: 34 / 39

SV-iS7 CANopen Manual

Trans Mode according to the Transmission Type value:

0: at the occurrence of SYNC, the CANopen Option creates TPDO, which is transmitted only when the

data has been changed from the previous value.

1~240: receiving SYNC for preset frequency, the TPDO is transmitted once.

252: at every occurrence of SYNC, data is updated to PDO, and TPDO is transmitted when the master

transmits a remote frame requesting TPDO.

253: receiving the remote frame from the master requesting the TPDO, data is updated and TPDO is

transmitted.

254: Manufacturer defined (in the IS7 CANopen, TPDO is transmitted at every Event Time.)

255: transmits TPDO by Event Trigger. If the data is not changes within the Event Time, TPDO is

transmitted. It the data changes within the Event Time, the TPDO is transmitted after Inhibit Time.

TPDO is not transmitted until the Inhibit Time has been passed.

6.2.4 TPDO

mapping

The map of the IS7 CANopen is fixed; therefore, user cannot edit the map.

6.2.4.1 TPDO1

mapping

The PDO set up in the CiA 402 Profile.

Index: 0x1A00

The table below presents the PDO1 Map.

Sub

index

Setting

value

Parameter

Index

Parameter Sub Index The name of parameter

0x01 0x60410010 0x6041

Statusword

0x02 0x60440010 0x6044

velocity

actual

value

6.2.4.2 TPDO3

mapping

The PDO set up in the LS Drive Profile.

Index: 0x1A02

The table below presents the PDO3 Map.

Sub

index

Setting

value

Parameter

Index

Parameter Sub Index The name of parameter

0x01

0x30000010

0x3000

Para Status - 1 Data Value

0x02

0x30010010

0x3001

Para Status - 2 Data Value

0x03

0x30020010

0x3002

Para Status - 3 Data Value

0x04

0x30030010

0x3003

Para Status - 4 Data Value

Para Status –x Data Value is to read the parameter of the communication address set up by COM-31~34.

Содержание SV-iS7 CANopen








































Результаты поиска

Содержание SV-iS7 CANopen

Отзывы:

LSIS SV-iS7 CANopen, Руководство пользователя, Страница: 34 / 39

Результаты поиска

Содержание SV-iS7 CANopen

Отзывы: