manualshive.com logo in svg

LSIS LSPV Series, Руководство пользователя, Страница: 52 / 60

Поделиться
Скачать
LSIS LSPV Series Скачать руководство пользователя страница 52

  

 

 

 

 

51 

Error 

code 

Error message 

Description 

Action 

0x0E0027 

DC current regis-

tration 

Failure of DC current con-

verter 

Contact the Service. 

0x0E0028 

Invalid country of 

use 

Country code is missing 

Input the country code at 
the initial installation. (It can 
be changed only service 
personnel.)  

0x0E0029 

Power supply fault 

1 

ENS function fault 

Contact the Service. 

0x0E002B Insulation 

1 

Insulation measurement 

fault 

Upon entry into the 
ACTIVATION phase, the 
acknowledge signal of the 
REFU insulation measuring 
instrument (at digital input 
X17 pin 8) must at LOW 
level. If this is not the case, 
the inverter emits the “Insu-
lation 1” error. 
Check the insulation of the 
system. 

0x0E002C Insulation 

2 

Insulation measurement 

fault 

Insulation measurements 
are taken in the ACTIVA-
TION phase. 
If the ISO measuring in-
strument (at digital input 
X17 pin 8) fails to give posi-
tive feedback after the 
maximum measuring time 
has elapsed, there is an 
insulation fault. 
Where the LSPV 500K + 
630K is concerned, the in-
sulation measuring instru-
ment is polled even during 
ongoing operation. 
Check the insulation of the 
system. 

0x0E002D 

AC current 

measurement 

Failure of DC current con-

verter 

Contact the Service. 

0x0E002F 

DC voltage 1 

Different DC voltages at 

stack 1 and stack 2  

The DC link voltages at WR 
stack 1 and WR stack 2 
must be identical. 
Allowed difference: 30V. 
Check the function and 
contact the Service.  

0x0E0031 

Lightning protec-

tion 

Fault through lightning pro-

tection element  

Check the lightning protec-
tion. Exchange if neces-
sary. Reset.  

Содержание LSPV Series





























































Отзывы:

Нет отзывов