manualshive.com logo in svg

LSIS LSPV Series, Руководство пользователя, Страница: 48 / 60

Поделиться
Скачать
LSIS LSPV Series Скачать руководство пользователя страница 48

  

 

 

 

 

47 

Error 

code 

Error message 

Description 

Action 

0A0010 

Undervoltage 

phase 

Detecting line  

undervoltage  

on outside conductor 

Possibly caused by switch-

ing actions on the net. Re-

measure line voltage. 

Service if line voltage is 

within normal range 

0A0011 Frequency 

FLL 

Detecting a power error 

(FLL) 

Check system frequency 

and line voltage. 

Service if system frequency 

is within normal range 

0A0012 Frequency 

Detecting a system fre-

quency error 

Check system frequency 

and line voltage. 

Service if system frequency 

is within normal range 

0A0013  PV isolation AFISR

AFI check 

Check insulation of the sys-

tem. 

0A0014 

No national code 

no national code is ad-

justed 

Service 

0A0100 

Power sec error 

mess 

Error message from power 

section 

There are further errors. 

See error memory. 

0A0101 

System fault LT1 

Unknown fault of power 

stack detected 

Service 

0A0102 

Overtemperature 

LT1 

Overtemperature of the 

right part of the heat sink 

Allow the unit to cool down.

Acknowledge error 

0A0103 

Overtemperature 

LT2 

Overtemperature inside of 

the inverter (sensor in the 

upper left area) 

Allow the unit to cool down.

Acknowledge error 

0A0104 

Overtemperature 

LT3 

Overtemperature inside of 

the inverter (sensor in the 

lower right area) 

Allow the unit to cool down.

Acknowledge error 

0A0105 

Overtemperature 

LT4 

Overtemperature of the left 

part of the heat sink 

Allow the unit to cool down.

Acknowledge error 

0A0106 

Supply voltage LT

Faulty supply voltage at 

power section 

Service 

0A0107 

System fault LT7 

Unknown fault of power 

stack detected 

Service 

0A0108 Frequency 

LT 

Error of system frequency 

of power section 

Check system frequency 

and line voltage. 

Service if system frequency 

is within normal range 

0A0109 Overvoltage 

LT 

Line overvoltage detector of 

power section 

Remeasure line voltage 

Service if line voltage is 

within normal range 

0A010A Undervoltage 

LT 

Line undervoltage detector 

of power section 

Remeasure line voltage 

Service if line voltage is 

within normal range 

0A010B 

System fault LT11

Unknown fault of power 

stack detected 

Service 

Содержание LSPV Series





























































Отзывы:

Нет отзывов