LSIS LSPV Series Скачать руководство пользователя страница 51

Страница: 51 / 60

Error

code

Error message

Description

Action

0x0E0013 Precharge

Precharge

failure

Restart if DC power has
increased.
Contact the Service if the
error occurs repeatedly.

0x0E0015

Precharge contac-

tor

Precharge cont. failure

Contact the Service.

0x0E0016 DC main contactor

DC contactor failure

Contact the Service.

0x0E0017 AC main contactor

AC contactor failure

Contact the Service.

0x0E0018 Overtemperature 4

Overtemperature of

microcontroller

Gerät abkühlen lassen.
Fehler quittieren

0x0E0019

Line voltage 2

Line voltage outside of

normal range

3AC-Spannungen gegen N-
Leiter messen

0x0E001A Solar cell voltage 1

Solar cell voltage above
maximum value

DC-Spannung messen,
Verschaltung der Strings
richtigstellen

0x0E001B Solar cell voltage 2

Solar cell voltage below
minimum value

DC-Spannung messen,
Verschaltung der Strings
richtigstellen

0x0E001C Supply

vltage

Fault of the supply

voltages of the power sec-

tion

Contact the Service.

0x0E001D Overtemperature 5

Controller

overtemperature

Allow the unit to cool down.
Contact the Service.

0x0E001E Communication

Problem in communication

between the control and the

power section

Acknowledge error.
Contact the Service if the
error occurs repeatedly.

0x0E0021

ENS power supply

fault

External ENS fault

External ENS fault present
at digital input X17 pin 1:
Repair the external fault
and restart.

0x0E0022

AC switch

AC switch not turned on

Check the switch function.
Contact the Service.

0x0E0023 Overtemperature 8

Overtemperature of power

transformer

Let the device cool down.
Contact the Service.

0x0E0024 DC

overcurrent

DC overcurrent from solar

cells

Acknowledge error.
Contact the Service if the
error occurs repeatedly.

0x0E0025 Overtemperature 7

Power section overtem-

perature

Let the device cool down.
Contact the Service.

0x0E0026 Pre-magnetization

Failure of magnetization

Power transformer

Wait until the current con-
troller has adjusted and
pre-magnetization is com-
pleted.
If you cannot acknowledge
the error, contact the
Service.

Содержание LSPV Series





























































Результаты поиска

Содержание LSPV Series

Отзывы:

LSIS LSPV Series, Руководство пользователя, Страница: 51 / 60

Результаты поиска

Содержание LSPV Series

Отзывы: