LS LL3301 Скачать руководство пользователя | Manualshive

Страница: 8 / 46

background image

SAFETY DECALS

Safety Decal Locations

Important:

Decal 03L01, 03L06, AL1105, AL1107 located on the right hand Mid-mount and Decal 03L02, 03L03, 03L04

located on the loader left hand Mid-Mount are visible when getting on tractor.

Care of Safety Decals.

▶

Keep safety decals clean and free of obstructing material.

▶

Clean safety decals with soap and water and dry with a soft cloth.

▶

If a component with a safety decal(s) affixed is replaced with a new
part, make sure new safety decal(s) are attached in the same location(s)
as the replaced components.

▶

Mount new safety decals by applying on a clean dry surface and pressing
air bubbles to outside edges.

40381557 (03L01) 40381563 (03L02) 40381564 (03L03)

40381565 (03L04) 40381558 (03L06) 40383693 (AL1105) 40383694 (AL1107)

40381560 (17L02)

40381559 (17L01)

40381561 (17L03)

40381835 (17L00)

«
...
6
7
8
9
10
...
»

Содержание LL3301















































Отзывы:

Нет отзывов

Похожие инструкции для LL3301

HiTech T Series

Бренд: Valtra Страницы: 31

Бренд: Zetor Страницы: 134

Бренд: Cub Cadet Страницы: 48

Бренд: Belarus Страницы: 125

Бренд: Iseki Страницы: 113

Бренд: Wallenstein Страницы: 52

Бренд: Eagle Страницы: 22

Бренд: MASSEY FERGUSON Страницы: 15

Бренд: MASSEY FERGUSON Страницы: 36

Бренд: Sears Страницы: 32

TRAC-LIFT T50SS

Бренд: JAWA Страницы: 11

TRAC-LIFT T50HLSS

Бренд: JAWA Страницы: 11

Бренд: Homelite Страницы: 2

Бренд: Homelite Страницы: 2

Бренд: Field Tuff Страницы: 7

Бренд: Field Tuff Страницы: 6

Бренд: Charles Страницы: 252

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды