LS LL3301 Скачать руководство пользователя | Manualshive

Страница: 41 / 46

background image

LOADER INSTALLATION

◈ Position the loader on a hard level surface. The more level the surface the easier the loader is to install.

▶ IMPORTANT: Do not tighten any hardware until all components are attached onto the tractor.

CAUTION: Lift and support all loader components safely.

▶

Using a hoist, install Mounting Frame LH/RH.

(1) Mounting Frame LH-1EA
(2) Mounting Frame RH-1EA
(3) BACK AXLE -1EA
(4) UNDER PLATE-1EA
(5) BRACKET ASSY-1EA
(6) BOLT, M10x45L-2EA
(7) SPRING WASHER, M10-4EA
(8) PLAIN WASHER, M10-2EA
(9) BOLT, M10x40Lx1.5P-2EA
(10) NUT, M10-2EA
(11) PLAIN WASHER, M12-4EA

(12) BOLT, M12x40L-2EA
(13) SPRING WASHER, M12-4EA
(14) NUT, M12-2EA
(15) BOLT, M12x50L-2EA
(16) SPRING WASHER, M14-20EA
(17) BOLT, M14x35L-6EA
(18) BOLT, M14x45L-4EA
(19) NUT, M14-6EA
(20) BOLT, M14x55L-2EA
(21) BOLT, M14x60L-4EA
(22) BOLT, M14x90L-4EA

«
...
39
40
41
42
43
...
»

Содержание LL3301















































Отзывы:

Нет отзывов

Похожие инструкции для LL3301

Бренд: AVANT Страницы: 24

KIOTI UD28-A901AF

Бренд: Daedong Страницы: 11

Sovereign 494-3112

Бренд: Simplicity Страницы: 40

Бренд: Belarus Страницы: 223

Бренд: Cub Cadet Страницы: 40

PROXIMA POWER Z90 2012

Бренд: Zetor Страницы: 222

Monogram ZCG3100VBB

Бренд: GE Страницы: 2

Бренд: ahlmann Страницы: 18

Бренд: Cub Cadet Страницы: 36

Бренд: MTD Страницы: 33

Бренд: SASFORKS Страницы: 22

Wheel Horse 523Dxi

Бренд: Toro Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды