Loveshaw LD16AP Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 39

background image

LOVESHAW an

ITW

COMPANY 7

INSTALLATION

THE LD16A MACHINE IS SHIPPED COMPLETELY ASSEMBLED.

TO UNPACK MACHINE, LIFT OFF THE UPPER CRATE, THEN UNFASTEN SKID. LIFT MACHINE

FROM SKID AND PULL SKID AWAY. REMOVE ALL PACKING MATERIAL THAT IS USED TO SECURE

THE HEAD AND CARTRIDGE.

THE BED HEIGHT OF THE MACHINE SHOULD BE ALIGNED WITH THE ROLLER HEIGHT OF THE

CONVEYOR. THE MACHINE SHOULD BE CENTERED ON THE INFEED CONVEYOR ROLLER. THE

MACHINE SHOULD THEN BE LEVELED. THE STRIPPER PLATE SHOULD BE USED TO ADJUST ANY

MINOR HEIGHT DIFFERENCES.

AFTER THE MACHINE IS IN PLACE AND LEVEL, CONNECT THE MACHINE TO AN APPROPRIATE

GROUNDED ELECTRICAL CONNECTION, (SEE MACHINE SPECIFICATION LABEL FOR VOLTAGE).

CONNECT THE AIR SUPPLY TO AN AIR SOURCE. MINIMUM LINE PRESSURE - 70 LBS. (5 kg/cm

²

).

TO START MACHINE, LOAD THE TAPE CARTRIDGES WITH TAPE AND THREAD THE TAPE. SEE

TAPE THREADING DIAGRAM.

THE MACHINE IS NOW READY FOR OPERATION. PLEASE NOTE THAT IN ORDER TO START THE

MACHINE, THE SAFETY GATES MUST BE CLOSED. WHEN THE SAFETY GATES ARE OPENED, THE

MACHINE WILL AUTOMATICALLY SHUT DOWN.

«
...
6
7
8
9
10
...
»

Содержание LD16AP








































Отзывы:

Нет отзывов

Похожие инструкции для LD16AP

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: Dairyland Страницы: 21

Бренд: Dairyland Страницы: 5

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

PowerXL DX-NET-ETHERNET2-2

Бренд: Eaton Страницы: 48

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Бренд: Xycom Страницы: 99

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: Fenton Страницы: 16

Бренд: TC Electronic Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды