background image

APPLYING POWER TO THE IF-4

Included with the IF-4 is a power supply (120V/12Vdc).  Connect the small end of the 90° female plug 

into the 12Vdc jack, located on the input side.  Then connect the two-prong large end into a standard 
110/120V electrical outlet.

Turn ON/OFF power switch, located behind green power LED to ON position.  The green LED will 

illuminate, indicating power to the system.  The system will now provide audio to the DVR, Soundcard 
Module, IP Network Camera, etc.

AUDIO LEVEL ADJUSTMENT

Located on the input side are potentiometers (round, with adjustment arrow) for each microphone.  
This is for adjusting the audio gain and to prevent overdriving or underdriving the audio signal.

The adjustment arrows are shipped in the straight-up position.  Turn slowly counterclockwise to lower 
the gain, and clockwise to increase.  This will provide the desired level of audio signal into the Audio 
Receiving Device (DVR, Soundcard Module, etc.).  A full turn clockwise increases the gain to 10dB.  A 
full turn counterclockwise will decrease the gain -30dB.

AUDIO TEST SWITCH

The purpose of this switch is to indicate the presence of audio and to assure the user that the IF-4 is 

driving the audio signals into the audio input of receiving device (DVR, IP Network Camera, Video 
Server, Soundcard module, etc.)

Located on the audio output side of IF-4 is a DIP switch labeled Audio Test Switch.   To the left of the 

switch is a red LED marked Audio Indicator.

For testing:

    1)  Select a zone that has a microphone connected to the microphone terminal block. 
              IF-4 utilizes pins 1-4.  
    2)  Push pin to the ON position.  The red LED will illuminate, indicating audio is present.  

With short bursts of audio, the LED will flicker and with continuous flow of audio LED 
illumination is constant.  Only one microphone can be tested at a time

NOTE: When testing is complete, all pins of the DIP switch must be in 

the OFF (down) position.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 4

LOUROE  ELECTRONICS    6 9 5 5   VA L J E A N   AVENUE,  VAN  NUYS,  CA  91406

TEL  (818)  994-6498

FAX 

994-6458

website: www.louroe.com                          e-mail: [email protected]

   

   

(818)

®

Ask4_304_inst_2/15

Содержание ASK-4 304

Страница 1: ...S West Penn 452 or equivalent MICROPHONE CONNECTIONS Located at the bottom of the Verifact A microphone is a 3 pin terminal block marked A B and C A 12Vdc power B Audio output of microphone C Ground If using the recommended wiring West Penn 452 connect as follows Red wire goes to terminal A of microphone Black wire goes to terminal B of microphone Bare wire goes to terminal C of microphone After a...

Страница 2: ...ise increases the gain to 10dB A full turn counterclockwise will decrease the gain 30dB AUDIO TEST SWITCH The purpose of this switch is to indicate the presence of audio and to assure the user that the IF 4 is driving the audio signals into the audio input of receiving device DVR IP Network Camera Video Server Soundcard module etc Located on the audio output side of IF 4 is a DIP switch labeled Au...

Страница 3: ...ophones VERIFACT A B C D D V E K L DT are compatible with Louroe IF 2 IF 4 and IF 8 Audio Interface Adapters Verifact A Microphone shown as an example with IF 4 Interface Adapter IF 4 will accommodate up to 4 Louroe microphones Back side of Verifact A Microphone Shown 2 3 4 LOUROE MODEL IF 4 AUDIO INTERFACE ADAPTER AUDIO OUT AUDIO IN RCA CABLE CONNECTS FROM AUDIO OUT OF IF 4 TO AUDIO IN OF DVR ETC...

Страница 4: ...t the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship Should a defect appear within one year 12 months from date of shipment LOUROE ELECTRONICS will at its sole discretion repair or replace the defective equipment This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS This warranty do...

Отзывы: