Lord MicroStrain 3DM-GX4-45 Скачать руководство пользователя страница 39

Страница: 39 / 78

3DM-GX4

™

-45

™

Inertial Navigation System

User Manual

Performance Optimization

5.3

Heading Drift and Compensation

There are four options for the heading reference source: GPS velocity, the magnetometer, an

external reference, or none. If the setting is an external reference, the user has to provide a

heading reference (for example,

see GPS External Receiver on page 54

). If the setting is none,

the estimated heading will drift with the drift of the gyroscopes. If the setting is the

magnetometer, there will be no drift, but the accuracy will only be as good as the

magnetometer. If using GPS velocity as a heading reference, the sensor (or sensor platform)

has to be moving, or there will be no heading reading. Moving the platform in a dynamic way will

assist in recapturing the heading (for example, slight s-turns in an aircraft which has been

traveling in a straight line for an extended period of time).

To select between the heading sources in MIP Monitor select Settings > Device > Estimation

Filter > EF Options.

Figure 28 -

Heading Source Setting

Содержание 3DM-GX4-45















































































Результаты поиска

Содержание 3DM-GX4-45

Отзывы:

Lord MicroStrain 3DM-GX4-45, Руководство пользователя, Страница: 39 / 78

Результаты поиска

Содержание 3DM-GX4-45

Отзывы: