LORCH MicorMIG 300 Скачать руководство пользователя

Страница: 62 / 68

page 62

Reading out machine data

Since the software version 1.12 from the 30th November 2015 it is possible to read out machine data using a

smartphone. Depending on the existing front panel the data can be transferred with different methods:

front panel

read out via

Basic, BasicPlus NFC
ControlPro

NFC, QR-code

The following data can be read out:

- software versions

- information- and error messages

- operating hour counters

machine configuration

- actual settings and welding parameters

Read out via NFC

A smartphone with NFC functions is required. To read out the data follow these steps:

Basic/BasicPlus:

switch off the machine

- press the menu button (upper-left button) and keep it pressed

- switch on the machine

- release the menu button

ControlPro:

switch off the machine

- press the menu button A50 and keep it pressed

- switch on the machine with the button pressed

- release the menu button A50

The machine shows “nFc Act” at the front panel.

In this condition a smartphone with NFC functions must be held to the front panel. The

machine transfers the data to the smartphone and accesses a Lorch web site automati-

cally that displays the data:

The email address of the user/technician can be put into the field “E-Mail” and hit the

button “Send E-Mail”. A PDF with the data is then send to the e-mail address that was

entered.

Содержание MicorMIG 300





































































Результаты поиска

Содержание MicorMIG 300

Отзывы:

Похожие инструкции для MicorMIG 300

Бренды по названию

Популярные бренды

LORCH MicorMIG 300, Руководство по обслуживанию

Результаты поиска

Содержание MicorMIG 300

Отзывы:

Похожие инструкции для MicorMIG 300

Бренды по названию

Популярные бренды