LORCH MicorMIG 300 Скачать руководство пользователя

Страница: 47 / 68

page 47

The temperature sensors are temperature dependant NTC resistors. As soon as one of the sensors is measur-

ing a too high temperature, the machine stops with

E01

“Overtemperature”. The sub-code indicates which sensor

detected the overtemperature. The fans keep running to cool down the machine. If the temperature drops below

55°C, the error code disappears and the machine can be used again.

The middle heat sink temperature is calculated over a longer period of time. The effective limit is depending on

the actual current setting, that means if the machine is used with a welding current below the 100% duty cycle, the

E01-04

can never come up.

sensor

code limit

monitoring

output diodes

E01-01

ca. 80°C

MAPRO

primary modules

E01-02

ca. 70°C

DRV

middle heatsink temperature E01-04 current depending

MAPRO

If one of the sensors should be faulty or disconnected from the measuring circuits, the machine will stop with the

error code

E13

“Error Temperature Sensor”.

The sensors have a resistance value of about 10k

Ω

at 25°C.

code sensor

E13-01 at output diodes
E13-02 inside primary modules (MicorMIG 300/350) / MOSFETs and IGBTs (MicorMIG 400/500)

Содержание MicorMIG 300





































































Результаты поиска

Содержание MicorMIG 300

Отзывы:

Похожие инструкции для MicorMIG 300

Бренды по названию

Популярные бренды

LORCH MicorMIG 300, Руководство по обслуживанию

Результаты поиска

Содержание MicorMIG 300

Отзывы:

Похожие инструкции для MicorMIG 300

Бренды по названию

Популярные бренды