London Electronics INTUITIVE INT4-P Скачать руководство пользователя страница 42

Страница: 42 / 44

Record of Revisions

6 February 2017

Filter response selector jumpers added

13 March 2019

Input resistance changed to 2 Ohms

Equipment Specifications

Bezel size

48mm high by 96 mm wide (1/8 DIN)

Panel Cutout

45 mm high by 92 mm wide

Case Depth

125 mm including connectors

Weight

300 grammes

Case Material

Black polycarbonate

Connectors

Detachable Screw Terminal connectors

Environmental

Storage Temperature range -20 to +70C, non condensing
Operating temperature range 0 to 50C, non condensing
Front sealed IP65. Optional cover SPC4 for IP67

Power

100-240 VAC, 45 to 60Hz or 11-30 VDC optional

Burden

10VA maximum

Input Signals (bipolar)

0-10V, 0-5V, 1-5V, 0-10mA, 0-20mA, 4-20mA

Input Resistance

1 Megohm for voltage, 2 Ohms for current inputs

Accuracy

+/-0.05% of range. Allow 30 minutes after switch-on, for thermal
stabilisation.

Span tempco

25 ppm/Degree Celsius

Zero Tempco

30 ppm/Degree Celsius

24V Excitation voltage

24VDC nominal rated at 60mA

10V Excitation voltage

10VDC nominal rated at 20mA

Filtering

/ smoothing

Selectable time constants of 0 to 25 seconds.
A/D is preceded by an active low pass filter with 7Hz cutoff point.

A/D conversion

Sigma-Delta 10 conversions per second, 50/60Hz rejection
Resolution 1 in 400 000 max. over full range

Display update rate

10 readings per second.

Display Range (max)

-199999 to +199999, depending on available signal level.

Plug-In Output Options

Analogue, Alarm, ASCII and Clock Options

See separate output manual for details.

Содержание INTUITIVE INT4-P













































Результаты поиска

Содержание INTUITIVE INT4-P

Отзывы:

Похожие инструкции для INTUITIVE INT4-P

Бренды по названию

Популярные бренды

London Electronics INTUITIVE INT4-P, Инструкция по установке и эксплуатации

Результаты поиска

Содержание INTUITIVE INT4-P

Отзывы:

Похожие инструкции для INTUITIVE INT4-P

Бренды по названию

Популярные бренды